Fujifilm FinePix T500 Motherboard Replacement

Introduction

A device's motherboard is the center of its operations. Any problems with it will cause the device to malfunction. Depending on the severity of the damage to the motherboard, replacement may be necessary, and this guide will show you how to do that.

Ce dont vous avez besoin

Étape 1 LCD Screen

Fujifilm FinePix T500 Motherboard Replacement, LCD Screen: étape 1, image 1 de 3

Fujifilm FinePix T500 Motherboard Replacement, LCD Screen: étape 1, image 2 de 3

Fujifilm FinePix T500 Motherboard Replacement, LCD Screen: étape 1, image 3 de 3

Unscrew the six 3.5mm Philips head from the outer casing.

Modifier

Étape 2

Fujifilm FinePix T500 Motherboard Replacement: étape 2, image 3 de 3

Open the battery chamber and remove the battery.
Pry the front half of the casing from the camera.
Be careful that the sensor cover—the small piece of translucent plastic—doesn't fall out of place. Return it to its original location if it does.

Modifier

Étape 3

Pry the back half of the casing from the camera.
Be careful when maneuvering the camera without the casing on as the LCD screen is not fastened to anything.

Modifier

Étape 4

Fujifilm FinePix T500 Motherboard Replacement: étape 4, image 3 de 3

Lift the LCD screen out of the camera.
There is a tab that keeps in place the ribbon that attaches the screen and motherboard. Lift this up using the spudger and disconnect the screen from the motherboard.

Modifier

Étape 5 Lens

Fujifilm FinePix T500 Motherboard Replacement, Lens: étape 5, image 1 de 1

Unscrew the 3.5 mm Phillips head screw from the corner of the camera.

Modifier

Étape 6

Fujifilm FinePix T500 Motherboard Replacement: étape 6, image 3 de 3

Pry the center casing off the camera. This is best done by separating the top and side sections individually.

Modifier

Étape 7

Fujifilm FinePix T500 Motherboard Replacement: étape 7, image 3 de 3

Unscrew the two 3.5 mm Phillips head screws in the metal plate.

Modifier

Étape 8

Pry the metal plate out using the spudger.

Modifier

Étape 9

Fujifilm FinePix T500 Motherboard Replacement: étape 9, image 3 de 3

Peel back the strip of black tape to reveal a red and black wire.
Detach the orange ribbon by gently pulling on it.
Detach the golden ribbon by gently lifting it with the spudger.

Modifier

Étape 10

The lens should now be free to simply be pushed out of its socket.
The black and red wires that were exposed previously may be in the way of removing the lens and may break. If they do, you will need to solder these wires back into place upon reassembly.

Modifier

Étape 11 Motherboard

Fujifilm FinePix T500 Motherboard Replacement, Motherboard: étape 11, image 1 de 1

Outil utilisé dans cette étape :

Tweezers

$4.99

J'achète

Use tweezers to pull back the plastic covering the top of the camera.

Modifier

Étape 12

Use tweezers to disconnect both the red and the black wires located next to the flash of the camera.
These wires will need to be soldered back in place upon reassembly.

Modifier

Étape 13

Pry off the top circuit board using the spudger.

Modifier

Étape 14

Use tweezers to disconnect the blue and white wires on the underside of the camera.
These wires will need to be soldered back in place upon reassembly.

Modifier