Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Boutique

Introduction

The battery on the Garmin Nuvi 200W is prone to losing charge over time. It can also fail due to unknown causes, which will require a replacement.

This repair is best done in a clean, dust-free environment. The sensitive electronics inside the Nuvi 200W will not respond will to sand and other small particles. It is also important to leave yourself ample time to effectively navigate the battery removal process.

  1. Peel off the sticker in order to find the two Torx T5 screws. Peel off the sticker in order to find the two Torx T5 screws. Peel off the sticker in order to find the two Torx T5 screws.
    • Peel off the sticker in order to find the two Torx T5 screws.

  2. Remove the two 4mm T5 Torx screws.
    • Remove the two 4mm T5 Torx screws.

  3. Carefully, using your plastic opening tools find the crease which separates the front and rear covers. Once you have a little gap, work it around the whole device with the tool to get separation. There is a ribbon cable between the two covers, be very careful when taking them apart to not damage the ribbon.
    • Carefully, using your plastic opening tools find the crease which separates the front and rear covers.

    • Once you have a little gap, work it around the whole device with the tool to get separation.

    • There is a ribbon cable between the two covers, be very careful when taking them apart to not damage the ribbon.

  4. OUVRIR TOUS LES ONGLETS

    Kits de mise à jour de RAM pour Mac

    Voir les kits

    Assez de RAM
    pour ouvrir tous les onglets

    Voir les kits
  5. After the case front and rear are separated, carefully lay the two sides down without disconnecting or damaging the orange ribbon cable. After the case front and rear are separated, carefully lay the two sides down without disconnecting or damaging the orange ribbon cable.
    • After the case front and rear are separated, carefully lay the two sides down without disconnecting or damaging the orange ribbon cable.

  6. Carefully use the black spudger to lift the white retaining clamp on the display cable ZIF connector. Make sure to lift up on the white retaining clamp and not the ZIF connector itself. Slide the orange ribbon cable away from the ZIF connector.
    • Carefully use the black spudger to lift the white retaining clamp on the display cable ZIF connector.

    • Make sure to lift up on the white retaining clamp and not the ZIF connector itself.

    • Slide the orange ribbon cable away from the ZIF connector.

  7. Using a screw driver, unscrew the four 2mm screws holding the motherboard in place. Gently lift the motherboard away from the rear cover. Take care to not damage the wires or ports that link the motherboard to other components.
    • Using a screw driver, unscrew the four 2mm screws holding the motherboard in place.

    • Gently lift the motherboard away from the rear cover. Take care to not damage the wires or ports that link the motherboard to other components.

  8. Using the black spudger, apply pressure to nudge the  plug out of its port. Repeat this process for both ports. Repeat this process for both ports.
    • Using the black spudger, apply pressure to nudge the plug out of its port.

    • Repeat this process for both ports.

  9. Using your opening tools, separate the battery from the top side. Very slowly push your tool down into the crevice. Be careful because the battery is glued to the rear cover, so it does take some force to separate. Once you have a gap big enough, pull the battery off the cover.
    • Using your opening tools, separate the battery from the top side. Very slowly push your tool down into the crevice.

    • Be careful because the battery is glued to the rear cover, so it does take some force to separate.

    • Once you have a gap big enough, pull the battery off the cover.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Matthew Eires

Membre depuis le 08/03/2017

319 Réputation

3 tutoriels rédigés

Équipe

UMass Dartmouth, Team S5-G4, Botvin Spring 2017 Membre de l'équipe UMass Dartmouth, Team S5-G4, Botvin Spring 2017

UMASSD-BOTVIN-S17S5G4

3 membres

6 tutoriels rédigés

Thank you for the guide as it is very helpful! Here's the replacement battery needed for the Garmin Nuvi 200W. It's brand new, it comes with all the necessary installation tools and it has a 1 year warranty! Garmin Nuvi 200W Replacement Battery

Mike - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 9

Total : 210