Aller au contenu principal

GoPro Hero 3 Silver Image Sensor Replacement

Ce dont vous avez besoin

  1. GoPro Hero 3 Silver Image Sensor Replacement, Battery: étape 1, image 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement, Battery: étape 1, image 2 de 2
    • Pull back on the tab on the back of GoPro to open the battery cover.

  2. GoPro Hero 3 Silver Image Sensor Replacement: étape 2, image 1 de 1
    • Pull the battery out using the tab.

  3. GoPro Hero 3 Silver Image Sensor Replacement, Image Sensor: étape 3, image 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement, Image Sensor: étape 3, image 2 de 2
    • Use the plastic opening tool to remove the faceplate.

    • There is some adhesive and clips so be careful and the faceplate should pop right off.

  4. GoPro Hero 3 Silver Image Sensor Replacement: étape 4, image 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement: étape 4, image 2 de 2
    • Now that the faceplate is off, it is time to remove the 4 screws on each corner.

    • Use the T4 tool bit from the iFixit toolkit in order to remove the 4 screws on each corner.

  5. GoPro Hero 3 Silver Image Sensor Replacement: étape 5, image 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement: étape 5, image 2 de 2
    • Note: Make sure you remove the door cover of the USB, mini HDMI, and SD port before. Separating the motherboard will be easier.

    • Using the plastic opening tool, slowly pry open the motherboard assembly.

  6. GoPro Hero 3 Silver Image Sensor Replacement: étape 6, image 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement: étape 6, image 2 de 2
    • Use the spudger to gently pry off the connector of the housing to the motherboard.

    • You should now have the motherboard assembly and the housing separated.

  7. GoPro Hero 3 Silver Image Sensor Replacement: étape 7, image 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement: étape 7, image 2 de 2
    • Use the spudger to remove the heat shield tape and detach the image sensor from the motherboard.

    • Using the T4 Torx toolbit, remove the 4 screws that connect the sensor to the lens.

  8. GoPro Hero 3 Silver Image Sensor Replacement: étape 8, image 1 de 2 GoPro Hero 3 Silver Image Sensor Replacement: étape 8, image 2 de 2
    • Remove the silver connector of the image sensor from the motherboard using the spudger to pry it off.

    • You should now be able to remove the image sensor by simply pulling it.

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autres ont terminé cette réparation.

Jose Villa

Membre depuis le 04/01/15

297 Réputation

1 tutoriel rédigé

Équipe

Cal Poly, Team 24-7, Lancaster Spring 2015 Membre de l'équipe Cal Poly, Team 24-7, Lancaster Spring 2015

CPSU-LANCASTER-S15S24G7

3 membres

21 tutoriels rédigés

2 commentaires

After the sensor has been replaced, does the camera need any catibration?

enrilazaro - Réponse

Your pictures are really dark.

Nick Ruiz - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 5

Total : 1,849