Réparez vos affaires Communauté Boutique

GoPro Hero 3 Silver LCD Housing Replacement

Introduction

Use this guide to replace the LCD housing on your GoPro Hero3 Silver.

Ce dont vous avez besoin

  1. GoPro Hero 3 Silver LCD Housing Replacement, Battery: étape 1, image 1 de 2 GoPro Hero 3 Silver LCD Housing Replacement, Battery: étape 1, image 2 de 2

    • Pull back on the tab on the back of GoPro to open the battery cover.

    Modifier

  2. GoPro Hero 3 Silver LCD Housing Replacement: étape 2, image 1 de 1

    • Pull the battery out using the tab.

    Modifier

  3. GoPro Hero 3 Silver LCD Housing Replacement, LCD Housing: étape 3, image 1 de 2 GoPro Hero 3 Silver LCD Housing Replacement, LCD Housing: étape 3, image 2 de 2

    • Use the plastic opening tool to remove the faceplate.

    • There is some adhesive and clips so be careful and the faceplate should pop right off.

    Modifier

  4. GoPro Hero 3 Silver LCD Housing Replacement: étape 4, image 1 de 2 GoPro Hero 3 Silver LCD Housing Replacement: étape 4, image 2 de 2

    • Now that the faceplate is off, it is time to remove the 4 screws on each corner.

    • Use the T4 tool bit from the iFixit toolkit in order to remove the 4 screws on each corner.

    Modifier

  6. GoPro Hero 3 Silver LCD Housing Replacement: étape 5, image 1 de 2 GoPro Hero 3 Silver LCD Housing Replacement: étape 5, image 2 de 2

    • Note: Make sure you remove the door cover of the USB, mini HDMI, and SD port before. Separating the motherboard will be easier.

    • Using the plastic opening tool, slowly pry open the motherboard assembly.

    Modifier

  7. GoPro Hero 3 Silver LCD Housing Replacement: étape 6, image 1 de 2 GoPro Hero 3 Silver LCD Housing Replacement: étape 6, image 2 de 2

    • Use the spudger to gently pry off the connector of the housing to the motherboard.

    • You should now have the motherboard assembly and the housing separated.

    Modifier

  8. GoPro Hero 3 Silver LCD Housing Replacement: étape 7, image 1 de 3 GoPro Hero 3 Silver LCD Housing Replacement: étape 7, image 2 de 3 GoPro Hero 3 Silver LCD Housing Replacement: étape 7, image 3 de 3

    • Use the spudger to remove the heat shield tape and detach the image sensor from the motherboard.

    • Using the T4 Torx toolbit, remove the 4 screws that connect the sensor to the lens.

    • Remove the silver connector of the image sensor from the motherboard using the spudger to pry it off.

    Modifier

  9. GoPro Hero 3 Silver LCD Housing Replacement: étape 8, image 1 de 3 GoPro Hero 3 Silver LCD Housing Replacement: étape 8, image 2 de 3 GoPro Hero 3 Silver LCD Housing Replacement: étape 8, image 3 de 3

    • The media adapter is attached to the motherboard via 3 screws:

    • x1 T4 Torx

    • x2 Phillips #00

    • There's a little silver bracket that is held down by the Phillips #00 screw so be careful not to lose it.

    • With a little prying, use the spudger to detach the media adapter's connector from the motherboard.

    Modifier

  10. GoPro Hero 3 Silver LCD Housing Replacement: étape 9, image 1 de 3 GoPro Hero 3 Silver LCD Housing Replacement: étape 9, image 2 de 3 GoPro Hero 3 Silver LCD Housing Replacement: étape 9, image 3 de 3

    • Use the spudger to lift the black tab up to unlock.

    • Then remove LCD screen connector by sliding out.

    Modifier

  11. GoPro Hero 3 Silver LCD Housing Replacement: étape 10, image 1 de 3 GoPro Hero 3 Silver LCD Housing Replacement: étape 10, image 2 de 3 GoPro Hero 3 Silver LCD Housing Replacement: étape 10, image 3 de 3

    • Using the Phillips head bit, remove the silver screw near the the top edge of the board.

    • Separate the LCD assembly by pulling away the motherboard.

    Modifier

  12. GoPro Hero 3 Silver LCD Housing Replacement: étape 11, image 1 de 2 GoPro Hero 3 Silver LCD Housing Replacement: étape 11, image 2 de 2

    • There are 3 Phillips #00 screws holding the lens onto the LCD housing that need to be removed.

    • Our screw on the top right is stripped, which is why it looks different. However, they will all look the same in your device.

    Modifier

  13. GoPro Hero 3 Silver LCD Housing Replacement: étape 12, image 1 de 2 GoPro Hero 3 Silver LCD Housing Replacement: étape 12, image 2 de 2

    • Carefully remove the camera lens from the LCD Housing.

    • Now you have the LCD housing removed!

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

5 autres ont terminé cette réparation.

Auteur

avec 5 autres contributeurs

Brian Alvarez

Membre depuis le 04/02/15

1 439 Réputation

6 tutoriels rédigés

Badges: 15

+ 12 badges supplémentaires

Équipe

Cal Poly, Team 24-7, Lancaster Spring 2015 Membre de l'équipe Cal Poly, Team 24-7, Lancaster Spring 2015

CPSU-LANCASTER-S15S24G7

3 membres

21 tutoriels rédigés

Un commentaire

Excellent walkthrough. Thank you Brian!

Nick Goulet - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 2

7 derniers jours : 5

30 derniers jours : 20

Total : 8,677