Aller au contenu principal

GoPro Hero5 Black Motherboard Replacement

Ce dont vous avez besoin

  1. GoPro Hero5 Black Motherboard Replacement, Battery: étape 1, image 1 de 3 GoPro Hero5 Black Motherboard Replacement, Battery: étape 1, image 2 de 3 GoPro Hero5 Black Motherboard Replacement, Battery: étape 1, image 3 de 3
    • While pressing the button on the bottom of the GoPro, slide the battery door to the side to pop it open.

  2. GoPro Hero5 Black Motherboard Replacement: étape 2, image 1 de 3 GoPro Hero5 Black Motherboard Replacement: étape 2, image 2 de 3 GoPro Hero5 Black Motherboard Replacement: étape 2, image 3 de 3
    • Grab the plastic flap on the battery and pull the battery out.

  3. GoPro Hero5 Black Motherboard Replacement, Back Housing: étape 3, image 1 de 2 GoPro Hero5 Black Motherboard Replacement, Back Housing: étape 3, image 2 de 2
    • Pull and twist the lens cover right or left until it pops off.

    • The lens cover is secured tightly and might be difficult to twist off.

  4. GoPro Hero5 Black Motherboard Replacement: étape 4, image 1 de 1
    • This step is not necessary but will make the process of removing the faceplate much easier.

    • Refer to the iOpener instructions for how to heat up and use the iOpener.

    • Apply the heated iOpener to the front of the GoPro for a few minutes to melt the adhesive under the faceplate.

    • The heated iOpener is very hot and can burn your hands. Avoid burns by using towels or gloves to hold the iOpener.

  5. GoPro Hero5 Black Motherboard Replacement: étape 5, image 1 de 3 GoPro Hero5 Black Motherboard Replacement: étape 5, image 2 de 3 GoPro Hero5 Black Motherboard Replacement: étape 5, image 3 de 3
    • Starting with the edges, use the spudger to pry off the faceplate.

    • The faceplate is held down with adhesive and may take a while to get off.

  6. GoPro Hero5 Black Motherboard Replacement: étape 6, image 1 de 2 GoPro Hero5 Black Motherboard Replacement: étape 6, image 2 de 2
    • Remove the six T3 Torx screws.

  7. GoPro Hero5 Black Motherboard Replacement: étape 7, image 1 de 3 GoPro Hero5 Black Motherboard Replacement: étape 7, image 2 de 3 GoPro Hero5 Black Motherboard Replacement: étape 7, image 3 de 3
    • Be careful when pulling open the motherboard assembly as it is still connected to the back housing by four cables. The cables may break if stretched.

    • Using the spudger, slowly pry open the motherboard assembly from the LCD side of the GoPro.

  8. GoPro Hero5 Black Motherboard Replacement: étape 8, image 1 de 3 GoPro Hero5 Black Motherboard Replacement: étape 8, image 2 de 3 GoPro Hero5 Black Motherboard Replacement: étape 8, image 3 de 3
    • Use the flat end of a spudger to pry the three ribbon cables connected to the side of the motherboard.

  9. GoPro Hero5 Black Motherboard Replacement: étape 9, image 1 de 2 GoPro Hero5 Black Motherboard Replacement: étape 9, image 2 de 2
    • Use the flat end of the spudger to pry the battery housing power cable straight up from its socket on the motherboard.

  10. GoPro Hero5 Black Motherboard Replacement, Motherboard: étape 10, image 1 de 1
    • Use the flat end of the spudger to pry the black cover plate straight up from its socket on the motherboard.

  11. GoPro Hero5 Black Motherboard Replacement: étape 11, image 1 de 1
    • Use the tweezers to pull the ribbon cable connector out of its white socket on the charging assembly board.

  12. GoPro Hero5 Black Motherboard Replacement: étape 12, image 1 de 2 GoPro Hero5 Black Motherboard Replacement: étape 12, image 2 de 2
    • Remove the two #000 Phillips screw.

  13. GoPro Hero5 Black Motherboard Replacement: étape 13, image 1 de 2 GoPro Hero5 Black Motherboard Replacement: étape 13, image 2 de 2
    • Use the flat end of the spudger to pry the charging port ribbon cable connector straight up from its socket on the motherboard.

    • Once the ribbon cable is disconnected from the motherboard. The charging port assembly should come right off.

  14. GoPro Hero5 Black Motherboard Replacement: étape 14, image 1 de 2 GoPro Hero5 Black Motherboard Replacement: étape 14, image 2 de 2
    • Remove the 10mm #000 Phillips screw.

  15. GoPro Hero5 Black Motherboard Replacement: étape 15, image 1 de 1
    • Remove the charging assembly housing by pulling it straight up off the motherboard.

  16. GoPro Hero5 Black Motherboard Replacement: étape 16, image 1 de 2 GoPro Hero5 Black Motherboard Replacement: étape 16, image 2 de 2
    • Remove the two 6mm #000 Phillips screws.

    • Remove the two 2mm #000 Phillips screws.

  17. GoPro Hero5 Black Motherboard Replacement: étape 17, image 1 de 1
    • Use the flat end of the spudger to pry the lens assembly ribbon cable connector straight up from its socket on the motherboard.

  18. GoPro Hero5 Black Motherboard Replacement: étape 18, image 1 de 1
    • Use the flat end of the spudger to pry the LCD screen ribbon cable connector straight up from its socket on the motherboard.

  19. GoPro Hero5 Black Motherboard Replacement: étape 19, image 1 de 3 GoPro Hero5 Black Motherboard Replacement: étape 19, image 2 de 3 GoPro Hero5 Black Motherboard Replacement: étape 19, image 3 de 3
    • Use the flat end of the spudger to pry the motherboard off the midframe.

    • The motherboard is held onto the midframe with light adhesive and should come right off with a little force.

Conclusion

To reassemble your device, follow these instructions in reverse order.

20 autres ont terminé cette réparation.

Christopher Adams

Membre depuis le 10/03/16

2 091 Réputation

5 tutoriels rédigés

Équipe

Cal Poly, Team 18-6, Forte Fall 2016 Membre de l'équipe Cal Poly, Team 18-6, Forte Fall 2016

CPSU-FORTE-F16S18G6

4 membres

22 tutoriels rédigés

11 commentaires

Hi

I took off only faceplate. Do you guys have an idea how to make it waterproof again? What can be used as an adhesive? Thanks

ramone4 - Réponse

you can try silicone glue, although obviously there is no guarantee to what extent it would be waterproof.

mattatron4 -

I think you better use an extra waterproof case to put your GP5 in it

Loic - Réponse

I used this guide to replace the USB port in my GP5. Does anyone know of a good way to hold the face plate down once it’s been removed? Not looking to make it waterproof again, just trying to hold the faceplate down a little better.

Mario Wong - Réponse

I would try either a silicone- or cyanoacrylate- (super glue) based adhesive. You can try to peel off the blue gasket and/or sand where the two pieces meet for better adhesion.

mattatron4 -

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 2

7 derniers jours : 31

30 derniers jours : 152

Total : 25,885