Réparez vos affaires Communauté Boutique

HP Envy M6-1205DX Touchpad Replacement

Introduction

We will be showing you how to properly take apart your computer without causing damage. Replacing the touch pad is not as simple as one may thing. You will have to buy a full new face plate because the touch pad is built in.

Ce dont vous avez besoin

  1. HP Envy M6-1205DX Touchpad Replacement, Battery: étape 1, image 1 de 1

    • Lay the device face down to begin.

    Modifier

  2. HP Envy M6-1205DX Touchpad Replacement: étape 2, image 1 de 1

    • Slide the release mechanism to the left to release the battery.

    Modifier

  3. HP Envy M6-1205DX Touchpad Replacement: étape 3, image 1 de 2 HP Envy M6-1205DX Touchpad Replacement: étape 3, image 2 de 2

    • Remove the battery.

    Modifier

  4. HP Envy M6-1205DX Touchpad Replacement, Touchpad: étape 4, image 1 de 1

    • Using a Phillips #1, remove the 8 10.6mm screws.

    • Also using a Phillips #1, remove the 8.6mm screw.

    Modifier

  5. HP Envy M6-1205DX Touchpad Replacement: étape 5, image 1 de 1

    • Slide the center panel down to remove it.

    Modifier

  7. HP Envy M6-1205DX Touchpad Replacement: étape 6, image 1 de 1

    • Using a Phillips #1, remove the 3.5mm screw.

    • Our computer did not come with a hard drive so you should have one in the empty hole. We have marked where we believe the screws will be in orange.

    • Using a Phillips #1, remove the four 10.6mm screws.

    Modifier

    There is another screw to remove here, to the left of the big circle under the HDD

    Jacob Hudson - Réponse

  8. HP Envy M6-1205DX Touchpad Replacement: étape 7, image 1 de 1

    • Pull the disk drive out to remove it.

    Modifier

  9. HP Envy M6-1205DX Touchpad Replacement: étape 8, image 1 de 2 HP Envy M6-1205DX Touchpad Replacement: étape 8, image 2 de 2

    • Using a Phillips #1, remove the two 2.4mm screws.

    Modifier

  10. HP Envy M6-1205DX Touchpad Replacement: étape 9, image 1 de 2 HP Envy M6-1205DX Touchpad Replacement: étape 9, image 2 de 2

    • Flip the black tab up on the clamp that holds the ribbon cable in place.

    • Pull the cable back with your fingers or a pair of tweezers.

    Modifier

  11. HP Envy M6-1205DX Touchpad Replacement: étape 10, image 1 de 2 HP Envy M6-1205DX Touchpad Replacement: étape 10, image 2 de 2

    • Flip the computer back over

    • Use the plastic opening tool to pry the keyboard up .

    Modifier

  12. HP Envy M6-1205DX Touchpad Replacement: étape 11, image 1 de 3 HP Envy M6-1205DX Touchpad Replacement: étape 11, image 2 de 3 HP Envy M6-1205DX Touchpad Replacement: étape 11, image 3 de 3

    • Carefully lift the keyboard up.

    • Flip up the black tab holding the large ribbon cable down.

    • Push both sides of the small white tab forward to release the small ribbon cable.

    • Pull both the cables out to remove them.

    • Remove the keyboard.

    Modifier

  13. HP Envy M6-1205DX Touchpad Replacement: étape 12, image 1 de 3 HP Envy M6-1205DX Touchpad Replacement: étape 12, image 2 de 3 HP Envy M6-1205DX Touchpad Replacement: étape 12, image 3 de 3

    • Flip the small white tab up to release the ribbon cable.

    • Pull to remove.

    • Repeat the same steps for the other cable.

    Modifier

  14. HP Envy M6-1205DX Touchpad Replacement: étape 13, image 1 de 1

    • Using a Phillips #1, remove the four 5.6mm silver screws.

    Modifier

  15. HP Envy M6-1205DX Touchpad Replacement: étape 14, image 1 de 2 HP Envy M6-1205DX Touchpad Replacement: étape 14, image 2 de 2

    • Use the plastic opening tool to pry the face plate off the rest of the frame.

    • Once you pry all of the snaps up lift the face plate off.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

3 autres ont terminé cette réparation.

Auteur

avec 3 autres contributeurs

Alex Wasilewski

Membre depuis le 09/28/16

596 Réputation

5 tutoriels rédigés

Badges: 16

+ 13 badges supplémentaires

Équipe

Eastern Washington University, Team 2-3, Mathisen Fall 2016 Membre de l'équipe Eastern Washington University, Team 2-3, Mathisen Fall 2016

EWU-MATHISEN-F16S2G3

5 membres

5 tutoriels rédigés

Un commentaire

I recently replaced my front face plate on my Envy M6, which originally had one in a natural silver finish. I can confirm that the onyx black one works equally well. To think it was a Lithuanian part too. I completed the guide, but mistakenly forgot to reconnect the touchpad ribbon. But that’s my fault.

Eric Shields - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 2

Total : 2,209