Introduction

This guide will help you replace your power adapter inside the printer.

Pièces

Aucune pièce nécessaire.

Turn off the printer and remove the power cable. Remove two 13mm T9 screws using a T9-Torx screwdriver. Turn counterclockwise  until the screws are released. Remove two 13mm T9 screws using a T9-Torx screwdriver. Turn counterclockwise  until the screws are released.
  • Turn off the printer and remove the power cable.

  • Remove two 13mm T9 screws using a T9-Torx screwdriver. Turn counterclockwise until the screws are released.

Ajouter un commentaire

Open the front door by placing your finger on the indented groove on the left side of the printer and pulling down This will give you access to the two T9-TORX 13mm screws that need to be removed to release the panel.
  • Open the front door by placing your finger on the indented groove on the left side of the printer and pulling down

  • This will give you access to the two T9-TORX 13mm screws that need to be removed to release the panel.

Ajouter un commentaire

Remove the two 13mm screws with a T9-TORX screwdriver by turning counter-clockwise (left). Remove the two 13mm screws with a T9-TORX screwdriver by turning counter-clockwise (left).
  • Remove the two 13mm screws with a T9-TORX screwdriver by turning counter-clockwise (left).

Ajouter un commentaire

Gently remove the left side panel by placing your palm flat against the surface and pulling down. Gently remove the left side panel by placing your palm flat against the surface and pulling down. Gently remove the left side panel by placing your palm flat against the surface and pulling down.
  • Gently remove the left side panel by placing your palm flat against the surface and pulling down.

Ajouter un commentaire

Remove two screws 13mm screws with a T9-Torx  screwdriver by rotating them counterclockwise. Remove two screws 13mm screws with a T9-Torx  screwdriver by rotating them counterclockwise. Remove two screws 13mm screws with a T9-Torx  screwdriver by rotating them counterclockwise.
  • Remove two screws 13mm screws with a T9-Torx screwdriver by rotating them counterclockwise.

Ajouter un commentaire

Unplug the black cable . Move all the cables and wires to the top of the motherboard to allow the power adapter underneath to be removed freely. Move all the cables and wires to the top of the motherboard to allow the power adapter underneath to be removed freely.
  • Unplug the black cable .

  • Move all the cables and wires to the top of the motherboard to allow the power adapter underneath to be removed freely.

Ajouter un commentaire

Gently bend the  black ribbon cable.
  • Gently bend the black ribbon cable.

  • Remove the four 8mm T8 screw underneath the ribbon cable by rotating it counterclockwise with a T8 -Torx screwdriver.

  • Take out the black plastic cover and the colored wires connected to it.

  • Now you have cleared a passage for the power adapter to be taken out.

Ajouter un commentaire

Gently pulling  out the power adapter.
  • Gently pulling out the power adapter.

  • Be careful with all the wires when pulling out the adapter.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Scott

Membre depuis le 24/01/2018

313 Réputation

3 tutoriels rédigés

Équipe

Cal Poly, Team S19-G2, Livingston Spring 2018 Membre de l'équipe Cal Poly, Team S19-G2, Livingston Spring 2018

CPSU-LIVINGSTON-S18S19G2

1 membre

3 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 20

Total : 120