Introduction

Before removing the LCD Monitor, follow these steps:

Shut down the computer

If unsure whether your computer is off or in hibernation, turn it on, and then shut down through the operating system.

Disconnect devices and power

Disconnect all external devices, plug-ins and power from the computer.

  1. Locate the battery on the bottom side of the laptop.
    • Locate the battery on the bottom side of the laptop.

    • Slide the release switch and the battery will pop out.

    • Remove the battery

    Ajouter un commentaire

  2. Using a Philips #1 Loosen the three 7mm captive screws that secure the memory module compartment cover to the computer.
    • Using a Philips #1 Loosen the three 7mm captive screws that secure the memory module compartment cover to the computer.

    • Lift the rear edge of the cover, swing it up and to the front, and remove the cover.

    Ajouter un commentaire

    • Loosen the two 6mm captive screws that secure the hard drive port bezel cover to the computer, using a Philips #1.

    • Lift the right side of the hard drive port bezel cover, swing it up and to the left, and remove the cover.

    Ajouter un commentaire

    • Use the Mylar tab to lift the hard drive up, and then slide it to the left to release it from the hard drive bay.

    Ajouter un commentaire

    • Disconnect the hard drive cable from the system board.

    • Remove the hard drive from the hard drive bay and set it aside.

    Ajouter un commentaire

    • With laptop upside down locate the three sets of screws that fasten the keyboard and switch cover.

      • Two Phillips 7mm screws that secure the switch cover to the computer.

      • Four Phillips 4.0mm screws that secure the switch cover to the computer. (these are inside the battery bay)

      • Four Philips 7mm screws that secure the keyboard to the computer.

    • Remove all ten screws.

    Ajouter un commentaire

  3. Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • Turn the computer over, and locate the Switch Cover.

    • Using the Safe Pry Tool, un-clip the Switch Cover until it detaches from the computer.

      • The clips will need careful prying to unhook.

    Ajouter un commentaire

    • Slide the Switch Cover onto the LCD Monitor, exposing the Speaker Assembly.

    • There are two ribbon cables still attached to the speaker assembly

    • Detach the two ribbon cables from the speaker assembly.

    Ajouter un commentaire

    • Remove the three silver Phillips 3.5mm screws that secure the keyboard to the computer.

    • Lift the rear edge of the keyboard and slide the keyboard back until the keyboard connector on the system board is accessible.

    Ajouter un commentaire

    • Unhinge the zero insertion force (ZIF) connector to release the ribbon cable then pull gently on the cable to release.

      • You need to unhinge the blue plastic to release the ribbon cable from the main board.

    • The keyboard can now be lifted off and set aside.

    Ajouter un commentaire

    • Remove the 3mm screw that secures the WLAN module to the computer. (The edge of the module opposite the slot rises away from the computer.)

    • Remove the WLAN module by pulling it away from the slot at an angle.

    • Disconnect the two WLAN antenna cables from the WLAN module.

    Ajouter un commentaire

    • Disconnect the display panel cable by use pulling upward on cable tabs.

    • Disconnect the webcam/microphone cable from the system board.

    • Remove the WLAN antenna cables and the webcam/ microphone cable from the clips built into the top cover.

    Ajouter un commentaire

    • Remove the four Phillips 7mm screws that secure the display assembly to the computer.

    • Lift the display assembly straight up and remove it.

    Ajouter un commentaire

    • Remove the two Phillips 5mm screws that secure the display hinge to the display panel.

      • The screws are behind plastic stickers and are very easy to bend.

    • Use a prying tool to flex the plastic around the monitor display to release the clips holding the display case together.

      • Use caution when using prying tool and avoid damaging bezel clips.

    Ajouter un commentaire

    • Remove the display bezel to uncover the LCD display

    • Remove eight screws that fasten the LCD display.

      • two Phillips PM2.5×5.0 screws from the top corners.

      • six Phillips M2.5×5.0 screws from the display hinges

    Ajouter un commentaire

    • Flex the bottom of the display panel and release the display hinges

    • Place the LCD Monitor next to the display panel by flipping it over the display hinges.

    • Disconnect the display LED cable from the display panel cable and remove the display panel.

    Ajouter un commentaire

    • Using the Philips #1, Remove four 7mm screws from the LCD Monitor frame.

      • There are two screws on each side of the LCD Monitor.

    • Remove the LCD Monitor from the frame.

    Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

6 autre(s) ont terminé cette réparation.

Chad

Membre depuis le 13/01/2014

949 Réputation

6 tutoriels rédigés

Équipe

Cal Poly, Team 10-34, Maness Winter 2014 Membre de l'équipe Cal Poly, Team 10-34, Maness Winter 2014

CPSU-MANESS-W14S10G34

4 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 2

7 derniers jours : 10

30 derniers jours : 39

Total : 4,219