Réparez vos affaires Communauté Boutique

HP Pavilion dv6700 Display/Monitor Replacement

Rédigé par : Alec Gramm (et 3 autres contributeurs)
  • Commentaires : 0
  • Favoris : 3
  • Réparations terminées : 2

Difficulté

Modérer

Étapes

18

Temps nécessaire

10 - 20 minutes

Sections

2

Drapeaux

2

Inconsistent Images

Images incohérentes

Actualiser les images pour les adapter aux conditions préalables augmenterait la qualité de ce tutoriel.

Bullets!

Puces !

Une bonne utilisation des balises, de la couleur et/ou du format des puces donnera de la clarté à ce tutoriel !

Introduction

This guide would be used if your screen gets damaged or no longer functions. All screws are a PH00 size. It would be advisable to keep track of which screws go where, as there are a lot of screws that will be removed over the course of this guide. Be sure to wear the anti-static guard strap, as that will protect the circuitry from permanent damage from static electricity.

  1. Locate the battery on the bottom of your laptop.

    • Locate the battery on the bottom of your laptop.

    Modifier

  2. Slide the tab all the way over to the left until battery pops out. Lift out and remove battery. Slide the tab all the way over to the left until battery pops out. Lift out and remove battery.

    • Slide the tab all the way over to the left until battery pops out. Lift out and remove battery.

    Modifier

  3. Remove the RAM port cover by unscrewing the two screws. These screws will can’t be fully removed because they’re captive. Loosen them until they turn freely.

    • Remove the RAM port cover by unscrewing the two screws.

    • These screws will can’t be fully removed because they’re captive. Loosen them until they turn freely.

    Modifier

  4. Remove Hard Disk Drive (HDD) cover by unscrewing the two screws. Screws will not fully remove. Loosen them until they turn freely.

    • Remove Hard Disk Drive (HDD) cover by unscrewing the two screws.

    • Screws will not fully remove. Loosen them until they turn freely.

    Modifier

  5. Remove screws from the bottom. Remove screws from the bottom. Remove screws from the bottom.

    • Remove screws from the bottom.

    Modifier

  6. Detach WiFi antenna wires. Be sure that the wires are labeled so you remember which ones go where. Be sure that the wires are labeled so you remember which ones go where.

    • Detach WiFi antenna wires.

    • Be sure that the wires are labeled so you remember which ones go where.

    Modifier

  8. Remove two screws. Use a needle-nose pliers to do the initial loosening, then switch to using a hex screwdriver (size 5) head to do the rest of the loosening. Use a needle-nose pliers to do the initial loosening, then switch to using a hex screwdriver (size 5) head to do the rest of the loosening.

    • Remove two screws.

    • Use a needle-nose pliers to do the initial loosening, then switch to using a hex screwdriver (size 5) head to do the rest of the loosening.

    Modifier

  9. Flip over HP Pavilion dv6700. Open up HP Pavilion dv6700.

    • Flip over HP Pavilion dv6700.

    • Open up HP Pavilion dv6700.

    Modifier

  10. Use plastic opening tool to pry open the plastic bar above the keyboard. Be careful not to yank so hard that you rip out the ribbon cables underneath. There is enough room to pull safely, but use control to prevent damage. Be careful not to yank so hard that you rip out the ribbon cables underneath. There is enough room to pull safely, but use control to prevent damage.

    • Use plastic opening tool to pry open the plastic bar above the keyboard.

    • Be careful not to yank so hard that you rip out the ribbon cables underneath. There is enough room to pull safely, but use control to prevent damage.

    Modifier

  11. Pull out and up on keyboard to remove it. Do not yank it all of the way out, as there is a ribbon cable underneath. Slide the two black locks on the side of the keyboard cable connection port up to release the cable.

    • Pull out and up on keyboard to remove it.

    • Do not yank it all of the way out, as there is a ribbon cable underneath.

    • Slide the two black locks on the side of the keyboard cable connection port up to release the cable.

    • Grip the ribbon cable near the connection point and gently but firmly pull it out.

    Modifier

  12. Flip over the plastic bar. Detach the display connector.

    • Flip over the plastic bar.

    • Detach the display connector.

    • Do not pull on the wires. Pull on the black plastic part or wedge a plastic opener or fingernail between the port and the connector.

    Modifier

  13. Detach the ribbon cables. Pull from the area closest to the connection port gently but firmly. Pull from the area closest to the connection port gently but firmly.

    • Detach the ribbon cables.

    • Pull from the area closest to the connection port gently but firmly.

    Modifier

  14. Pull up on tape holding down wires. Pull up on tape holding down wires. Pull up on tape holding down wires.

    • Pull up on tape holding down wires.

    Modifier

  15. Pull up on the WiFi wires and out from under the metal tabs. Do not yank them out. Let them hang loose once they are out from under the tabs. Do not yank them out. Let them hang loose once they are out from under the tabs.

    • Pull up on the WiFi wires and out from under the metal tabs.

    • Do not yank them out. Let them hang loose once they are out from under the tabs.

    Modifier

  16. Disconnect the connector from the port. Remove the wire from under the metal tabs. Let wire hang loose after removing under the tabs.

    • Disconnect the connector from the port.

    • Remove the wire from under the metal tabs.

    • Let wire hang loose after removing under the tabs.

    Modifier

  17. Remove the black screw in the top right corner. Remove the black screw in the top right corner.

    • Remove the black screw in the top right corner.

    Modifier

  18. Pull upward on the screen connector tab. It will be firmly secured, so don't be afraid to use a little extra force to pull it off.

    • Pull upward on the screen connector tab.

    • It will be firmly secured, so don't be afraid to use a little extra force to pull it off.

    Modifier

  19. Remove the black screw from the top left corner. Keep your hand on the screen to secure it, as once you remove this screw, it will come loose.

    • Remove the black screw from the top left corner.

    • Keep your hand on the screen to secure it, as once you remove this screw, it will come loose.

    • Lift the screen off and set it aside.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autres ont terminé cette réparation.

Auteur

avec 3 autres contributeurs

Alec Gramm

Membre depuis le 01/10/2015

1 228 Réputation

5 tutoriels rédigés

Badges: 10

+ 7 badges supplémentaires

Équipe

University of Illinois Urbana-Champaign, Team 1-118, Wolske Fall 2015 Membre de l'équipe University of Illinois Urbana-Champaign, Team 1-118, Wolske Fall 2015

UICU-WOLSKE-F15S1G118

1 membre

6 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 9

Total : 1,540