Aller au contenu principal

HP Photosmart 935 Plastic Casing Replacement

Ce dont vous avez besoin

  1. HP Photosmart 935 Plastic Casing Replacement, Batteries: étape 1, image 1 de 2 HP Photosmart 935 Plastic Casing Replacement, Batteries: étape 1, image 2 de 2
    • Flip the camera over so the bottom of the camera is facing you.

    • Turn the mode dial to the OFF position.

  2. HP Photosmart 935 Plastic Casing Replacement: étape 3, image 1 de 2 HP Photosmart 935 Plastic Casing Replacement: étape 3, image 2 de 2
    • Slide the bottom cover in the direction of the arrow to open it.

  3. HP Photosmart 935 Plastic Casing Replacement: étape 4, image 1 de 1
    • Pull out the batteries.

  4. HP Photosmart 935 Plastic Casing Replacement, Plastic Casing: étape 5, image 1 de 1
    • Use a Phillips #00 screwdriver to remove the two 4.7 mm screws in the bottom of the plastic casing.

  5. HP Photosmart 935 Plastic Casing Replacement: étape 6, image 1 de 2 HP Photosmart 935 Plastic Casing Replacement: étape 6, image 2 de 2
    • Remove the four 4.7 mm screws on the left side of the camera.

  6. HP Photosmart 935 Plastic Casing Replacement: étape 7, image 1 de 2 HP Photosmart 935 Plastic Casing Replacement: étape 7, image 2 de 2
    • Remove the four 4.7 mm screws on the opposite side of the camera.

  7. HP Photosmart 935 Plastic Casing Replacement: étape 8, image 1 de 3 HP Photosmart 935 Plastic Casing Replacement: étape 8, image 2 de 3 HP Photosmart 935 Plastic Casing Replacement: étape 8, image 3 de 3
    • Use your thumbs to pry the case apart.

    • It is easiest to pry the case apart if you start at the bottom.

    • The case should come apart with minimal effort. If it doesn't, you can use a spudger or plastic opening tool to pry it open.

  8. HP Photosmart 935 Plastic Casing Replacement: étape 9, image 1 de 1
    • This step requires a significant amount of force.

    • Pull the bottom half of the inner camera out of the case by half an inch. This may be difficult.

  9. HP Photosmart 935 Plastic Casing Replacement: étape 10, image 1 de 2 HP Photosmart 935 Plastic Casing Replacement: étape 10, image 2 de 2
    • While pulling the camera out of the case, note the small soft plastic cover on the side. This cover will detach from the rest of the device.

    • Once the bottom of the inner camera is pulled out, pull the device out completely.

    • Use a firm grasp when removing the device from the case for stability and control.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Clay Young

Membre depuis le 04/04/12

233 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 15-13, Forte Spring 2012 Membre de l'équipe Cal Poly, Team 15-13, Forte Spring 2012

CPSU-FORTE-S12S15G13

5 membres

10 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 8

Total : 1,725