Menu 

Vos paramètres

Mon établi

Accédez rapidement aux tutoriels, aux pièces et aux réponses correspondant à vos appareils
Mon panier (US Store)

On dirait que votre panier est vide

Parcourez notre boutique

HTC One S Rear Case Replacement

Rédigé par : Dante Mazzanti (et 2 autres contributeurs)
  • Commentaires : 39
  • Favoris : 3

Difficulté

Modérée

Étapes

11

Sections

2

Drapeaux

0

Introduction

Make your HTC One S look brand new with a new rear case.

Outils

Acheter ces outils

Pièces

Aucune pièce spécifiée.

  1. We recommend that you clean your microwave before proceeding, as any nasty gunk on the bottom may end up stuck to the iOpener. Place the iOpener in the center of the microwave.

    • We recommend that you clean your microwave before proceeding, as any nasty gunk on the bottom may end up stuck to the iOpener.

    • Place the iOpener in the center of the microwave.

    • For carousel microwaves: Make sure the plate spins freely. If your iOpener gets stuck, it may overheat and burn.

    Traduire

  2. Heat the iOpener for thirty seconds.

    • Heat the iOpener for thirty seconds.

    • Throughout the repair procedure, as the iOpener cools, reheat it in the microwave for an additional thirty seconds at a time.

    • Be careful not to overheat the iOpener during the repair. Overheating may cause the iOpener to burst.

    • Never touch the iOpener if it appears swollen.

    • If the iOpener is still too hot in the middle to touch, continue using it while waiting for it to cool down some more before reheating. A properly heated iOpener should stay warm for up to 10 minutes.

    Traduire

  3. Remove the iOpener from the microwave, holding it by one of the two flat ends to avoid the hot center.

    • Remove the iOpener from the microwave, holding it by one of the two flat ends to avoid the hot center.

    • The iOpener will be very hot, so be careful when handling it. Use an oven mitt if necessary.

    Traduire

  4. Handling it by the tag, place the heated iOpener across the bottom casing.

    • Handling it by the tag, place the heated iOpener across the bottom casing.

    • Let the iOpener sit for at least a minute to soften the adhesive beneath the casing.

    Traduire

  5. Batteries pour ordinateurs portables

    Une réparation facile pour un gain en puissance max.

    Acheter maintenant

    Batteries pour ordinateurs portables

    Une réparation facile pour un gain en puissance max.

    Acheter maintenant

  6. Gently place an opening pick in the corner of the gap between the bottom casing and rear case. Slide the opening pick along the side of the casing, prying it away from the adhesive as you go. Slide the opening pick along the side of the casing, prying it away from the adhesive as you go.

    • Gently place an opening pick in the corner of the gap between the bottom casing and rear case.

    • Slide the opening pick along the side of the casing, prying it away from the adhesive as you go.

    Traduire

  7. Use your fingers to pull the bottom casing off the rest of the phone.

    • Use your fingers to pull the bottom casing off the rest of the phone.

    Traduire

  8. Starting at the groove near the headphone jack, use a plastic opening tool to lift the top casing. Starting at the groove near the headphone jack, use a plastic opening tool to lift the top casing.

    • Starting at the groove near the headphone jack, use a plastic opening tool to lift the top casing.

    Traduire

  9. Use your fingers to pull the top casing off of the rest of the phone.

    • Use your fingers to pull the top casing off of the rest of the phone.

    Traduire

  10. Remove the following screws holding the rear case to the rest of the phone:

    • Remove the following screws holding the rear case to the rest of the phone:

    • Two 3.15 mm Phillips #00 screws

    • One 4.15 Torx T5 screw

    • One 4 mm Torx T5 screw

    Traduire

  11. Place your fingers on either side of the phone and gently push up on the rear case. It is important to start from the bottom of the phone because the rear case wraps around the front of the phone at the top which makes it impossible to start prying from there. It is important to start from the bottom of the phone because the rear case wraps around the front of the phone at the top which makes it impossible to start prying from there.

    • Place your fingers on either side of the phone and gently push up on the rear case.

    • It is important to start from the bottom of the phone because the rear case wraps around the front of the phone at the top which makes it impossible to start prying from there.

    Traduire

  12. Pull the rear case away from the rest of the phone with your hands.

    • Pull the rear case away from the rest of the phone with your hands.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 2 autres contributeurs

Dante Mazzanti

Membre depuis le 23/02/2015

563 Réputation

3 tutoriels rédigés

Badges: 9

+ 6 badges supplémentaires

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 2

Total : 1,272