Réparez vos affaires

Droit à la réparation

Boutique

Handspring Visor Deluxe PDA Touch Screen Replacement

Rédigé par : David Faltemier (et 4 autres contributeurs)
  • Commentaires : 0
  • Favoris : 0

Difficulté

Modérée

Étapes

9

Temps nécessaire

10 - 15 minutes

Sections

4

Drapeaux

0

Introduction

Use this guide to replace the Touch Screen.

  1. Remove the outer screen cover by releasing the top clip from the main body of the device. Remove the outer screen cover by releasing the top clip from the main body of the device.

    • Remove the outer screen cover by releasing the top clip from the main body of the device.

    Traduire

  2. Pull out the stylus from the top right corner of the device. Pull out the stylus from the top right corner of the device. Pull out the stylus from the top right corner of the device.

    • Pull out the stylus from the top right corner of the device.

    Traduire

  3. Slide the memory cartridge cover up and off the device. Slide the memory cartridge cover up and off the device. Slide the memory cartridge cover up and off the device.

    • Slide the memory cartridge cover up and off the device.

    Traduire

  4. Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète

    Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète

  5. Remove the battery cover by releasing the clip from the main body of the device. Remove the battery cover by releasing the clip from the main body of the device.

    • Remove the battery cover by releasing the clip from the main body of the device.

    Traduire

  6. Remove the batteries from the device.

    • Remove the batteries from the device.

    Traduire

  7. Unscrew the four 2.94mm screws with a #00 Phillips screwdriver.

    • Unscrew the four 2.94mm screws with a #00 Phillips screwdriver.

    • One end of the OEM stylus can unscrew and contains a mini #00 Phillips screwdriver.

    Traduire

  8. Use the spudger to pry open the casing by applying pressure at 4 clips on both sides of the device. Be careful while opening the casing as there is a flex strip connecting the two halves. Be careful while opening the casing as there is a flex strip connecting the two halves.

    • Use the spudger to pry open the casing by applying pressure at 4 clips on both sides of the device.

    • Be careful while opening the casing as there is a flex strip connecting the two halves.

    Traduire

  9. Disconnect the flex strip from the motherboard with tweezers. Disconnect the flex strip from the motherboard with tweezers. Disconnect the flex strip from the motherboard with tweezers.

    • Disconnect the flex strip from the motherboard with tweezers.

    Traduire

  10. Release the latch in bottom right corner of the touchscreen. Use the spudger (if needed) to pry the screen from the front case. Use the spudger (if needed) to pry the screen from the front case.

    • Release the latch in bottom right corner of the touchscreen.

    • Use the spudger (if needed) to pry the screen from the front case.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 4 autres contributeurs

David Faltemier

Membre depuis le 20/06/2012

19 Réputation

5 tutoriels rédigés

Badges: 8

+ 5 badges supplémentaires

Équipe

Cal Poly, Team 1-2, Regan SU 2012 Membre de l'équipe Cal Poly, Team 1-2, Regan SU 2012

CPSU-REGAN-SU12S1G2

4 membres

6 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 1

7 derniers jours : 3

30 derniers jours : 3

Total : 591