Réparez vos affaires Communauté Boutique

Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement

Introduction

After getting into the Hannspree Hannspad SN1AT71, the Camera is fairly easy to replace.

Ce dont vous avez besoin

  1. Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement, Back Panel: étape 1, image 1 de 1

    • Place the tablet screen side up.

    • Make sure the device is turned off to avoid damage.

    Modifier

  2. Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 2, image 1 de 2 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 2, image 2 de 2

    • Use the metal spudger to press an opening between the screen and back cover.

    • The plastic tabs are located on each corner of the back cover.

    • Be careful, as the plastic tabs are delicate.

    Modifier

  3. Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 3, image 1 de 1

    • Wedge the plastic opening tool between the screen and the back panel to prevent re-engagement

    Modifier

  4. Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 4, image 1 de 2 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 4, image 2 de 2

    • Slide the metal spudger around the casing to separate it from the inside of the tablet.

    Modifier

  6. Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 5, image 1 de 2 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 5, image 2 de 2

    • Flip the tablet over so the screen side is down after all the tabs are separated.

    • Remove the back panel by delicately lifting it straight up.

    Modifier

  7. Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement, Battery: étape 6, image 1 de 2 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement, Battery: étape 6, image 2 de 2

    • Remove the adhesive tape from the power connection cables.

    Modifier

  8. Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 7, image 1 de 3 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 7, image 2 de 3 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 7, image 3 de 3
    Outil utilisé dans cette étape :
    Tweezers
    $4.99
    J'achète

    • Instructions for desoldering can be found on the iFixit website.

    • The soldering iron is hot. It can burn you and it can cause damage to the wires and motherboard.

    • Grab hold of the red wire using the tweezers.

    • Desolder the red wire connection from the motherboard using the tip of the soldering iron.

    • Move the wire connection away from the motherboard.

    • Do not let the red wire connection touch other wires or the motherboard.

    Modifier

  9. Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 8, image 1 de 3 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 8, image 2 de 3 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 8, image 3 de 3

    • Desolder the black and yellow wire connection from the motherboard by following the previous step.

    • When moving the wire connections, do not let the red wire connection touch other wires or the motherboard.

    Modifier

  10. Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 9, image 1 de 3 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 9, image 2 de 3 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 9, image 3 de 3

    • Insert the flat end of the nylon spudger between the battery and the case.

    • The battery is connected to the tablet with an adhesive tape and will come free slowly.

    • Do not puncture or bend the battery while removing. If your battery is swollen, take appropriate precautions.

    Modifier

  11. Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement, Front and Rear Camera Replacement: étape 10, image 1 de 2 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement, Front and Rear Camera Replacement: étape 10, image 2 de 2

    • Identify the ribbon connecter attached to the camera and where it connects to the circuit board.

    • The two cameras are connected with one ribbon cable.

    • Zero insertion force connector.

    Modifier

  12. Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 11, image 1 de 3 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 11, image 2 de 3 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 11, image 3 de 3

    • Disconnect the sliding zero insertion force (ZIF). Use the plastic opening tool or a fingernail to slide the tab out, then pull the cable out.

    Modifier

  13. Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 12, image 1 de 3 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 12, image 2 de 3 Hannspree Hannspad SN1AT71 Front and Rear Camera Replacement: étape 12, image 3 de 3

    • Pull the cameras out of their resting places in a straight upward motion.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 6 autres contributeurs

matthew vandeventer

Membre depuis le 03/11/15

950 Réputation

5 tutoriels rédigés

Badges: 20

+ 17 badges supplémentaires

Équipe

Colorado Springs, Team 9-4, Panko Spring 2015 Membre de l'équipe Colorado Springs, Team 9-4, Panko Spring 2015

UCCS-PANKO-S15S9G4

3 membres

10 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 2

7 derniers jours : 4

30 derniers jours : 12

Total : 598