Réparez vos affaires Communauté Boutique

How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822

Introduction

Sometimes the moving about of computer speakers leads to broken wires and the speakers will fail to work properly. This guide will show you how to repair a Harman Kardon CN-04N567-48220 external computer speaker.

Ce dont vous avez besoin

  1. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822, How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 1, image 1 de 3 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822, How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 1, image 2 de 3 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822, How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 1, image 3 de 3

    • Use your fingers to pull the top of the speaker grill away from the speaker enclosure.

    • Pull the bottom of the grill away from the speaker enclosure and then completely remove the grill.

    • Four posts attach the grill assembly to the front of speaker enclosure. These posts are located on the back side of the grill assembly.

    Modifier

  2. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 2, image 1 de 2 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 2, image 2 de 2

    • Remove the top two 9.5 mm Phillips #1 screws from the speaker.

    • Remove the two 9.5 mm Phillips #1 screws located below the speaker screws.

    • Slowly work your way around the seam until the two parts of the enclosure are free.

    • More speaker cable slack may be achieved by pulling additional cable through the rear of the case.

    Modifier

  3. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 3, image 1 de 2 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 3, image 2 de 2

    • Inspect both sides of the printed circuit board (PCB) for any raised traces, off-colored areas, or loose components.

    • This step is to avoid making a mechanical repair (re-soldering the wires to the PCB) on a piece of equipment that also has obvious electrical or mechanical issues.

    Modifier

  5. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 4, image 1 de 1

    • Use desoldering braid and a soldering iron to wick away the old solder and wire remnants from the solder pads and through-holes.

    • Do not leave solder bridges across the pads as this will cause functional issues.

    Modifier

  6. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 5, image 1 de 2 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 5, image 2 de 2

    • Use wire strippers to remove a small section of insulation from the wires.

    • Use a soldering iron and solder to tin the wires. This prevents the strands from fraying.

    Modifier

  7. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 6, image 1 de 2 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 6, image 2 de 2

    • Insert the yellow wire into the through-hole marked "R".

    • Insert the bare ground wire into the through-hole marked "G".

    • Insert the white wire into the through-hole marked "L".

    Modifier

  8. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 7, image 1 de 1

    • Use the soldering iron to flow solder between each wire and its solder pad.

    Modifier

  9. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: étape 8, image 1 de 1

    • Reassemble the two parts of the enclosure making sure that the PCB-mounted audio jacks are lined up with the mating holes of the rear enclosure.

    • Route the cable inside the enclosure to avoid stressing the solder joints.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

8 autres ont terminé cette réparation.

Auteur

avec 2 autres contributeurs

Ken Gage

Membre depuis le 06/09/16

306 Réputation

1 tutoriel rédigé

Badges: 6

+ 3 badges supplémentaires

Équipe

Texas Tech, Team 3-1, Rauch SU 2016 Membre de l'équipe Texas Tech, Team 3-1, Rauch SU 2016

TTU-RAUCH-SU16S3G1

2 membres

3 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 12

30 derniers jours : 57

Total : 4,325