Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Pièces & Outils

Introduction

Use this guide to replace the back cover of your Huawei Mate 10 Pro.

If your battery is swollen, do not heat your phone. Swollen batteries can be very dangerous, so wear eye protection and exercise due caution, or take it to a professional if you're not sure how to proceed.

  1. Insert a SIM opening tool in the hole on the left side and push it in. Remove the SIM card tray.
    • Insert a SIM opening tool in the hole on the left side and push it in.

    • Remove the SIM card tray.

  2. Switch off your phone.
    • Switch off your phone.

    • Prepare an iOpener and apply it to the back of the phone for about two minutes to loosen the adhesive beneath the back cover.

    Erm… Simply impossible to open the phone this way…

    I used the iOpener for 2 mins as instructed, I’ve used even an hair drier for 30 secs on max power (could barely touch the phone after) and still with the suction tool I was not able to open the phone.

    It simply doesn’t budge!!!

    Miguel Oliveira - Réponse

  3. Essential Electronics Toolkit

    Petit kit. Grandes possibilités.

    Shop Toolkits

    Essential
    Electronics
    Toolkit

    Shop Toolkits
  4. Lift up the back cover with a suction cup until you can insert the flat end of a halberd spudger. Use the halberd spudger to cut the adhesive beneath the back cover on all sides of the phone. Use opening picks to avoid the adhesive from sticking to the back cover again while cutting the adhesive on all sides.
    • Lift up the back cover with a suction cup until you can insert the flat end of a halberd spudger.

    • Use the halberd spudger to cut the adhesive beneath the back cover on all sides of the phone.

    • Use opening picks to avoid the adhesive from sticking to the back cover again while cutting the adhesive on all sides.

    Faire attention à ne pas enfoncer trop le cutter/spatule hallebarde. Surtout à l’approche des boutons ON/OFF et volume, la nappe ne passe pas loin et se branche à coté de l’empreinte digitale.

    Bilan, j’ai coupé cette nappe et n’ai plus de bouton volume et on/off.

    Plus qu’à chercher la piece de rechange pendant que le telephone est ouvert ;)

    NeoX - Réponse

  5. Don't remove the back cover all the way, yet. The fingerprint sensor cable is still connected to motherboard. Flip the back cover over to the side.
    • Don't remove the back cover all the way, yet. The fingerprint sensor cable is still connected to motherboard.

    • Flip the back cover over to the side.

    • Remove the Phillips #00 screw which holds down the metal shield, sitting on top of the connection of the fingerprint sensor cable.

  6. Use a pair tweezers to remove the metal shield covering the connector of the fingerprint sensor. Disconnect the fingerprint sensor cable with a spudger.
    • Use a pair tweezers to remove the metal shield covering the connector of the fingerprint sensor.

    • Disconnect the fingerprint sensor cable with a spudger.

    • When reassembling your phone apply new adhesive where it is necessary.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Dominik Schnabelrauch

Membre depuis le 23/11/2016

59 855 Réputation

279 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

115 membres

11 127 tutoriels rédigés

Where can I buy the back part of the phone. Email me at brownpridebandit@gmail.com

Luis Liberato - Réponse

Thanks for good work you do

amoudi Guide - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 9

7 derniers jours : 80

30 derniers jours : 395

Total : 5,439