Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Boutique

Introduction

Use this guide to remove or replace the rear glass of the Huawei P20.

Opening the Huawei P20 will damage the splash and dust protection seals on the device. If you do not replace the adhesive seals, your phone will function normally but will lose its protection.

You’ll need replacement adhesive to reattach components when reassembling the device.

  1. Before you begin, switch off your phone.
    • Before you begin, switch off your phone.

    • Apply a heated iOpener to the back of the phone to loosen the adhesive beneath the back cover. Apply the iOpener for at least two minutes.

  2. Secure a suction handle to the bottom of the back cover, as close to the edge as possible. If the phone's rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed. Lift the back cover with the suction handle to create a small gap between the cover and the frame.
    • Secure a suction handle to the bottom of the back cover, as close to the edge as possible.

    • If the phone's rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.

    • Lift the back cover with the suction handle to create a small gap between the cover and the frame.

    • Insert an opening pick into the gap.

    • If you have trouble, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

    • Slide the opening pick to the bottom right corner.

  3. Insert a second opening pick and slide it to the bottom left corner  to cut the adhesive. Leave the opening picks in place to prevent the adhesive from resealing.
    • Insert a second opening pick and slide it to the bottom left corner to cut the adhesive.

    • Leave the opening picks in place to prevent the adhesive from resealing.

  4. Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète

    Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète
  5. Insert a third opening pick at the bottom left corner. In the next few steps whilst cutting around the power button and rear camera make sure you only use the tip of the opening pick to avoid cutting the cable, smearing the lens or damaging the camera. Start to slide the tip of the opening pick from the bottom left corner along the side of the phone to cut the adhesive.
    • Insert a third opening pick at the bottom left corner.

    • In the next few steps whilst cutting around the power button and rear camera make sure you only use the tip of the opening pick to avoid cutting the cable, smearing the lens or damaging the camera.

    • Start to slide the tip of the opening pick from the bottom left corner along the side of the phone to cut the adhesive.

    • Leave the opening pick in its place at the top left corner to prevent the adhesive from resealing.

  6. If the adhesive becomes hard to cut it most likely cooled down. Use your iOpener to reheat it. Insert a fourth opening pick under the top left corner of the back cover.
    • If the adhesive becomes hard to cut it most likely cooled down. Use your iOpener to reheat it.

    • Insert a fourth opening pick under the top left corner of the back cover.

    • Slide the opening pick along the top edge of the phone to cut the adhesive.

    • Leave the opening pick in the top right corner to prevent the adhesive from resealing.

  7. Insert a fifth opening pick at the top right corner of the phone. Slide the opening pick along the right side to cut the remaining adhesive.
    • Insert a fifth opening pick at the top right corner of the phone.

    • Slide the opening pick along the right side to cut the remaining adhesive.

  8. Lift and remove the back cover. Before installing fresh adhesive and reassembling, remove any remaining adhesive from the phone, and clean the glued areas with isopropyl alcohol and a lint-free cloth.
    • Lift and remove the back cover.

    • Before installing fresh adhesive and reassembling, remove any remaining adhesive from the phone, and clean the glued areas with isopropyl alcohol and a lint-free cloth.

Conclusion

Secure the new back cover with pre-cut adhesive or double-sided adhesive tape.

To reassemble your device, follow these instructions in reverse order.

After installing the rear glass, apply pressure for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers Community for troubleshooting help.

Une autre personne a terminé cette réparation.

Dominik Schnabelrauch

Membre depuis le 23/11/2016

76 742 Réputation

329 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

131 membres

13 426 tutoriels rédigés

Hi Dominic, nice guide

Nicu Gherghin - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 1

7 derniers jours : 4

30 derniers jours : 53

Total : 645