Aller au contenu principal

Huawei P20 Rear Glass Replacement

Ce dont vous avez besoin

  1. Huawei P20 Rear Glass Replacement, Rear Glass: étape 1, image 1 de 1
    • Before you begin, switch off your phone.

    • Apply a heated iOpener to the back of the phone to loosen the adhesive beneath the back cover. Apply the iOpener for at least two minutes.

    Hi guys fingerprint sensor on my Huawei p20 Pro stopped working but I didnt want to attempt screen removal as the chances of damaging the screen were high, but what if I could remove and replace the sensor without removing the screen at £6.00 a pop on ebay for a replacement sensor against a ton plus for a new screen, I opted to take a chance with the sensor, so I removed battery cover glass then all removable parts in the sensor area, once removed I could see a big enough gap to feed the sensor through, now the tricky part I smeared vaseline on the area of the sensor ribbon that fitted between frame and screen and carefully slid it between the frame and screen, now all that was left was to connect the sensor to the connector, there was no way that I could see to slide the ribbon under the frame to connect it so I laid it over that part of frame and connected it to the screen, before I replaced the sensor the phone wouldn't recognise it at all so I was relieved that it detected it now. Works perfectly.

    Blasphemy - Réponse

  2. Huawei P20 Rear Glass Replacement: étape 2, image 1 de 3 Huawei P20 Rear Glass Replacement: étape 2, image 2 de 3 Huawei P20 Rear Glass Replacement: étape 2, image 3 de 3
    • Secure a suction handle to the bottom of the back cover, as close to the edge as possible.

    • If the phone's rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.

    • Lift the back cover with the suction handle to create a small gap between the cover and the frame.

    • Insert an opening pick into the gap.

    • If you have trouble, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

    • Slide the opening pick to the bottom right corner.

  3. Huawei P20 Rear Glass Replacement: étape 3, image 1 de 2 Huawei P20 Rear Glass Replacement: étape 3, image 2 de 2
    • Insert a second opening pick and slide it to the bottom left corner to cut the adhesive.

    • Leave the opening picks in place to prevent the adhesive from resealing.

  4. Huawei P20 Rear Glass Replacement: étape 4, image 1 de 3 Huawei P20 Rear Glass Replacement: étape 4, image 2 de 3 Huawei P20 Rear Glass Replacement: étape 4, image 3 de 3
    • Insert a third opening pick at the bottom left corner.

    • In the next few steps whilst cutting around the power button and rear camera make sure you only use the tip of the opening pick to avoid cutting the cable, smearing the lens or damaging the camera.

    • Start to slide the tip of the opening pick from the bottom left corner along the side of the phone to cut the adhesive.

    • Leave the opening pick in its place at the top left corner to prevent the adhesive from resealing.

    Davor auch aufpassen da ist das Flexkabel des powerbuttons

    Maximilian Koos - Réponse

    Hi Maximilian,

    danke für deinen Hinweis. Du hast vollkommen Recht und ich habe den Warnhinweis entsprechend ergänzt.

    Dominik Schnabelrauch -

  5. Huawei P20 Rear Glass Replacement: étape 5, image 1 de 2 Huawei P20 Rear Glass Replacement: étape 5, image 2 de 2
    • If the adhesive becomes hard to cut it most likely cooled down. Use your iOpener to reheat it.

    • Insert a fourth opening pick under the top left corner of the back cover.

    • Slide the opening pick along the top edge of the phone to cut the adhesive.

    • Leave the opening pick in the top right corner to prevent the adhesive from resealing.

  6. Huawei P20 Rear Glass Replacement: étape 6, image 1 de 2 Huawei P20 Rear Glass Replacement: étape 6, image 2 de 2
    • Insert a fifth opening pick at the top right corner of the phone.

    • Slide the opening pick along the right side to cut the remaining adhesive.

  7. Huawei P20 Rear Glass Replacement: étape 7, image 1 de 2 Huawei P20 Rear Glass Replacement: étape 7, image 2 de 2
    • Lift and remove the back cover.

    • Before installing fresh adhesive and reassembling, remove any remaining adhesive from the phone, and clean the glued areas with isopropyl alcohol and a lint-free cloth.

Conclusion

Secure the new back cover with pre-cut adhesive or double-sided adhesive tape.

To reassemble your device, follow these instructions in reverse order.

After installing the rear glass, apply pressure for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers Community for troubleshooting help.

Une autre personne a terminé cette réparation.

Dominik Schnabelrauch

Membre depuis le 11/23/16

202 809 Réputation

682 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Staff

135 membres

16 732 tutoriels rédigés

2 commentaires

Hi Dominic, nice guide

Nicu Gherghin - Réponse

What size of adhesive should be used?

Jimmi Rasmussen - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 7

30 derniers jours : 57

Total : 3,507