Réparez vos affaires

Droit à la réparation

Boutique

Huawei P30 Pro Battery Replacement

En vedette

Rédigé par : Dominik Schnabelrauch (et 2 autres contributeurs)
  • Commentaires : 0
  • Favoris : 0
  • Réparations terminées : 1

Tutoriel vedette

Difficulté

Modérée

Étapes

25

Temps nécessaire

1 heure

Sections

7

Drapeaux

1

Featured Guide

Tutoriel vedette

L'équipe iFixit trouve ce tutoriel particulièrement réussi.

Introduction

Use this guide to replace a worn-out or dead battery in your Huawei P30 Pro.

Opening the Huawei P30 Pro will damage the waterproof sealing on the device. If you do not replace the adhesive seals, your phone will function normally but will lose its water-protection.

If your battery is swollen, take appropriate precautions. For your safety, discharge your battery below 25% before disassembling your phone. This reduces the risk of a dangerous thermal event if the battery is accidentally damaged during the repair.

Although it is possible to remove the battery without removing the main flex cable with the charging port, we recommend to do so to avoid damage to surrounding components.

You’ll need replacement adhesive to reattach components when reassembling the device.

  1. Before you begin, switch off your phone.

    • Before you begin, switch off your phone.

    • Apply a heated iOpener to the back of the phone to loosen the adhesive beneath the back cover. Apply the iOpener for at least two minutes.

    Traduire

  2. Secure a suction handle to the bottom of the back cover, as close to the edge as possible. If the phone's rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed. Lift the back cover with the suction handle to create a small gap between the cover and the frame.

    • Secure a suction handle to the bottom of the back cover, as close to the edge as possible.

    • If the phone's rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.

    • Lift the back cover with the suction handle to create a small gap between the cover and the frame.

    • Insert an opening pick into the gap.

    • If you have trouble, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

    • Slide the opening pick to the bottom right corner.

    Traduire

  3. Insert a second opening pick and slide it to the bottom left corner to cut the adhesive. Leave the opening picks in place to prevent the adhesive from resealing.

    • Insert a second opening pick and slide it to the bottom left corner to cut the adhesive.

    • Leave the opening picks in place to prevent the adhesive from resealing.

    Traduire

  4. Insert a third opening pick at the bottom left corner. In the next few steps whilst cutting around the rear camera make sure you only use the tip of the opening pick to avoid smearing the lens or damaging the camera. Slide the tip of the opening pick from the bottom left corner along the side of the phone to cut the adhesive.

    • Insert a third opening pick at the bottom left corner.

    • In the next few steps whilst cutting around the rear camera make sure you only use the tip of the opening pick to avoid smearing the lens or damaging the camera.

    • Slide the tip of the opening pick from the bottom left corner along the side of the phone to cut the adhesive.

    • Leave the opening pick in its place at the top left corner to prevent the adhesive from resealing.

    Traduire

  5. If the adhesive becomes hard to cut, it most likely cooled down. Use your iOpener to reheat it. Insert a fourth opening pick under the top left corner of the back cover.

    • If the adhesive becomes hard to cut, it most likely cooled down. Use your iOpener to reheat it.

    • Insert a fourth opening pick under the top left corner of the back cover.

    • Slide the opening pick along the top edge of the phone to cut the adhesive.

    • Leave the opening pick in the top right corner to prevent the adhesive from resealing.

    Traduire

  6. Insert a fifth opening pick at the top right corner of the phone. Slide the opening pick along the right side to cut the remaining adhesive.

    • Insert a fifth opening pick at the top right corner of the phone.

    • Slide the opening pick along the right side to cut the remaining adhesive.

    Traduire

  7. Lift and remove the back cover. Before installing fresh adhesive and reassembling, remove any remaining adhesive from the phone, and clean the glued areas with isopropyl alcohol and a lint-free cloth.

    • Lift and remove the back cover.

    • Before installing fresh adhesive and reassembling, remove any remaining adhesive from the phone, and clean the glued areas with isopropyl alcohol and a lint-free cloth.

    • During reassembly, this is a good point to power on your phone and test all functions before sealing it up. Be sure to power your phone back down completely before you continue working.

    • Secure the new back cover with pre-cut adhesive or double-sided adhesive tape. After installing the rear glass, apply pressure for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.

    Traduire

  8. Remove the ten Phillips #00 screws (4.3 mm length).

    • Remove the ten Phillips #00 screws (4.3 mm length).

    Traduire

  9. Slide an opening pick under the black adhesive at the bottom right of the charging coil. Carefully loosen the adhesive with the opening pick.

    • Slide an opening pick under the black adhesive at the bottom right of the charging coil.

    • Carefully loosen the adhesive with the opening pick.

    Traduire

  10. Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète

    Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète

  11. Slide an opening pick under the black adhesive at the bottom left of the charging coil. Carefully loosen the adhesive with the opening pick.

    • Slide an opening pick under the black adhesive at the bottom left of the charging coil.

    • Carefully loosen the adhesive with the opening pick.

    Traduire

  12. Slide an opening pick under the left side of the motherboard cover. Unhinge the left side of the motherboard cover by slightly rotating the opening pick.

    • Slide an opening pick under the left side of the motherboard cover.

    • Unhinge the left side of the motherboard cover by slightly rotating the opening pick.

    Traduire

  13. Push the motherboard cover out of the sockets at the top edge of the phone beginning with the top left corner. Remove the motherboard cover including the NFC and charging coil.

    • Push the motherboard cover out of the sockets at the top edge of the phone beginning with the top left corner.

    • Remove the motherboard cover including the NFC and charging coil.

    Traduire

  14. Use a spudger to pry up and disconnect the battery connector. When you disconnect connectors like these, be careful not to dislodge the small surface-mounted components surrounding the socket.

    • Use a spudger to pry up and disconnect the battery connector.

    • When you disconnect connectors like these, be careful not to dislodge the small surface-mounted components surrounding the socket.

    Traduire

  15. Remove the five Phillips #00 screws (4.3 mm length).

    • Remove the five Phillips #00 screws (4.3 mm length).

    • Some of these screws may be hidden under adhesive. Carefully peel the adhesive to uncover these screws.

    Traduire

  16. Slide an opening pick under the top edge of the daughterboard cover. Pry up and unhinge the daughterboard cover by slightly rotating the opening pick.

    • Slide an opening pick under the top edge of the daughterboard cover.

    • Pry up and unhinge the daughterboard cover by slightly rotating the opening pick.

    Traduire

  17. Remove the daughterboard cover. Remove the daughterboard cover.

    • Remove the daughterboard cover.

    Traduire

  18. Use a spudger to pry up and disconnect the left main flex cable connector from the motherboard. To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

    • Use a spudger to pry up and disconnect the left main flex cable connector from the motherboard.

    • To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

    Traduire

  19. Use a spudger to pry up and disconnect the right main flex cable connector from the motherboard. Use a spudger to pry up and disconnect the right main flex cable connector from the motherboard.

    • Use a spudger to pry up and disconnect the right main flex cable connector from the motherboard.

    Traduire

  20. Use a spudger to pry up and disconnect the main flex cable connector from the daughterboard. Use a spudger to pry up and disconnect the main flex cable connector from the daughterboard.

    • Use a spudger to pry up and disconnect the main flex cable connector from the daughterboard.

    Traduire

  21. Remove the main flex cable including the charging port by lifting it upwards and then pulling it in the direction of the motherboard. Remove the main flex cable including the charging port by lifting it upwards and then pulling it in the direction of the motherboard.

    • Remove the main flex cable including the charging port by lifting it upwards and then pulling it in the direction of the motherboard.

    Traduire

  22. Peel the orange adhesive strip labeled with a 1 off the battery. The orange adhesive tape will rip along a small perforated line. Peel the orange adhesive strip labeled with a 1 off the battery. The orange adhesive tape will rip along a small perforated line.

    • Peel the orange adhesive strip labeled with a 1 off the battery. The orange adhesive tape will rip along a small perforated line.

    Traduire

  23. Peel the orange adhesive strip labeled with a 2 off the battery. The orange adhesive tape will rip along a small perforated line. Peel the orange adhesive strip labeled with a 2 off the battery. The orange adhesive tape will rip along a small perforated line.

    • Peel the orange adhesive strip labeled with a 2 off the battery. The orange adhesive tape will rip along a small perforated line.

    Traduire

  24. Peel the orange adhesive strip labeled with a 3 off the battery. Pull up the orange adhesive strip to lift the battery out of its recess.

    • Peel the orange adhesive strip labeled with a 3 off the battery.

    • Pull up the orange adhesive strip to lift the battery out of its recess.

    • Although these new adhesive tabs are supposed to make the battery removal easier, these may require some force. In case you're having trouble removing the battery, you can apply a heated iOpener to the center of the display, to loosen the adhesive underneath.

    Traduire

  25. Swing the battery up to an upright position. Peel the battery off the remaining adhesive. Remove the battery.

    • Swing the battery up to an upright position.

    • Peel the battery off the remaining adhesive.

    • Remove the battery.

    • During re-assembly, temporarily re-connect the battery to the motherboard to help align it correctly. Disconnect the battery after it is seated.

    Traduire

  26. Peel the battery's adhesive sticker off the midframe. This step is mandatory if you are replacing the screen. However it is highly recommended to use a fresh adhesive sticker as well, when installing a new battery.

    • Peel the battery's adhesive sticker off the midframe.

    • This step is mandatory if you are replacing the screen. However it is highly recommended to use a fresh adhesive sticker as well, when installing a new battery.

    • Secure the new battery with pre-cut adhesive or double-sided adhesive tape. In order to position it correctly, apply the new adhesive into the phone at the places where the old adhesive was located, not directly onto the battery. Press the new battery firmly into place.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order. Apply new adhesive where necessary after cleaning the relevant areas with isopropyl alcohol (>90%).

For optimal performance, calibrate your newly installed battery: Charge it to 100%, and keep charging it for at least two more hours. Then, use it until it shuts off due to low battery. Finally, charge it uninterrupted to 100%

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Une autre personne a terminé cette réparation.

Auteur

avec 2 autres contributeurs

Dominik Schnabelrauch

Membre depuis le 23/11/2016

76 742 Réputation

329 tutoriels rédigés

Badges: 39

+ 36 badges supplémentaires

Équipe

iFixit Membre de l'équipe iFixit

Community

131 membres

13 426 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 15

7 derniers jours : 91

30 derniers jours : 418

Total : 3,674