Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Installation de RAM dans le Mac mini modèle A1176

Ce dont vous avez besoin

  1. Installation de RAM dans le Mac mini modèle A1176, Partie supérieure du boîtier: étape 1, image 1 de 2 Installation de RAM dans le Mac mini modèle A1176, Partie supérieure du boîtier: étape 1, image 2 de 2
    • Éteignez votre Mac mini, déconnectez tous les câbles et retournez-le.

    • Insérez la spatule Jimmy dans la jointure entre l'aluminium du couvercle supérieur e de la partie inférieure en plastique.

    • La spatule doit s'enfoncer d'environ 9 mm.

    A spackle knife makes these steps go much faster.

    jouniseppanen - Réponse

    A double sided letter opener or a thin non-serrated butter knife will suffice.

    To prenent cosmetic blemishes, place a matchbook cover or similar thin cardboard on the outer perimeter under the “jimmy”.

    Mike - Réponse

  2. Installation de RAM dans le Mac mini modèle A1176: étape 2, image 1 de 3 Installation de RAM dans le Mac mini modèle A1176: étape 2, image 2 de 3 Installation de RAM dans le Mac mini modèle A1176: étape 2, image 3 de 3
    • Penchez légèrement la spatule vers l'extérieur pour faire levier et élargir la fente et soulevez légèrement le boîtier inférieur.

    • Plusieurs clips en plastique sur le boîtier inférieur s’insèrent dans un canal du boîtier supérieur en aluminium. Votre objectif est de pousser ces clips suffisamment avec la spatule vers l’intérieur pour les dégager du canal, tout en tirant doucement le boîtier inférieur vers le haut.

    Patience is your best friend.

    Do not insert “jimmy in too far. Marking a line from tip upwards on the tool will prevent too far insertion, possibly breaking tabs or damaging internal components.

    To prevent the cover closing back up, small strips of matchbook cover (os equivalent) can be inserted about half inch hold prevent closure.

    Mike - Réponse

  3. Installation de RAM dans le Mac mini modèle A1176: étape 3, image 1 de 2 Installation de RAM dans le Mac mini modèle A1176: étape 3, image 2 de 2
    • Une fois que vous avez libéré le premier côté, faites pivoter le Mac mini et commencez à faire levier sur le bord avant.

    • Utilisez le même mouvement de levier pour replier les clips vers l’intérieur et soulever le boîtier inférieur afin de le sortir du boîtier supérieur.

  4. Installation de RAM dans le Mac mini modèle A1176: étape 4, image 1 de 2 Installation de RAM dans le Mac mini modèle A1176: étape 4, image 2 de 2
    • Vous devrez peut-être déplacer la spatule le long du bord pour ouvrir tous les clips. Soyez prudent et progressez petit à petit.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    Installation de RAM dans le Mac mini modèle A1176: étape 5, image 1 de 2 Installation de RAM dans le Mac mini modèle A1176: étape 5, image 2 de 2
    • Keep working around the perimeter, freeing the clips along the final edge.

  6. Installation de RAM dans le Mac mini modèle A1176: étape 6, image 1 de 2 Installation de RAM dans le Mac mini modèle A1176: étape 6, image 2 de 2
    • Retournez le Mac mini et soulevez le boîtier supérieur du boîtier inférieur.

    Before reassembly, make sure no wires are sticking out.

    Line up top cover carefully. Gently press down on top cover until top and bottom fully seated.

    CAUTION! DO NOT PRESS TOO HARD ON THE COVER TO PREVENT CRACKING THE PLASTIC TOP.

    GO EASY.

    Mike - Réponse

  7. Installation de RAM dans le Mac mini modèle A1176, Installation du cadre intérieur du Mac mini modèle A1176: étape 7, image 1 de 3 Installation de RAM dans le Mac mini modèle A1176, Installation du cadre intérieur du Mac mini modèle A1176: étape 7, image 2 de 3 Installation de RAM dans le Mac mini modèle A1176, Installation du cadre intérieur du Mac mini modèle A1176: étape 7, image 3 de 3
    • Plus loin dans ce guide, vous serez amené à retirer plusieurs vis Phillips cruciformes. Les embouts de tournevis sont généralement trop larges pour les fentes ; veillez à vous munir d'un tournevis Phillips à tige fine.

    • Commencez par retirer l'antenne AirPort (la plus grande des deux) située près du bouton de mise sous tension.

    • Exercez une légère pression sur les deux clips de fixation et soulevez l'antenne AirPort pour la libérer.

    • Si la pression est excessive, vous risquez de casser les deux clips de fixation. Procédez délicatement.

    • Lors de la réinstallation, vous devrez presser légèrement les deux clips de fixation pour les insérer dans les ouvertures de la carte d'antenne AirPort.

  8. Installation de RAM dans le Mac mini modèle A1176: étape 8, image 1 de 2 Installation de RAM dans le Mac mini modèle A1176: étape 8, image 2 de 2
    • À l'aide de la pointe d'un spudger, soulevez légèrement le côté gauche du dispositif de verrouillage du câble ZIF pour le sortir de la prise.

    • Le dispositif de verrouillage du câble se soulève d'environ 1 mm, puis se bloque. N'essayez pas de le retirer complètement.

    Now also lift the right side of the ZIF cable lock up from its socket.

    chriZ - Réponse

    Good catch of the incomplete unlocking instructions. ;P

    lamarhavard -

    Hmmm... what if I didn't read this before and I removed the cable and the lock sort of broke?... what would happen... would I experience problems? I can still put the cable back in place and push the lock back down with the spudger.

    Dan O - Réponse

    Same. I totally removed the lock , the edges are busted and won't stay in place, How can I get the cable to stay? what's the fix?

    Suzanne -

    Dan O & Suzanne, hold the cable in the socket and put a dab of hot glue on both sides, It's non-conductive and should hold...worked for me.

    lamarhavard -

    does any one know, where to get the connector from zhe ZIF Cable?

    someone, that preowned my mac broke the holder!

    julian gmeiner - Réponse

    Julian, did you ever find where to get a replacement lock for the Zip Cable. Mine is also broken..

    Suzanne -

    This is not my first memory replacement in a Mini and I got over-confident and stupidly fully removed the audio cable ZIF lock and assumed I had broken something. But, now that I have read this guide more carefully, I am not sure. I sure would love to hear some detailed instructions for putting a ZIF lock back on.

    Is it possible that I have removed it without having broken it? If I have broken it, do I have to buy a new cable? Just a new ZIF lock? A new audio board? This is a 2.0 GHz A1176.

    Thanks!

    GalvanicMacPro - Réponse

    Michael, Mine seems to be broken. I bought & tried the Kapton Tape that was suggested & still no sound.

    Suzanne -

    C’est la première que je doit déverrouiller un câble ZIF. Je précise qu’il faut lever à gauche et à droite, ça force un peu, prendre appui sur le boitier du Mac, comme e montre la photo.

    La partie noire reste dans la partie blanche (+1 mm), et la nappe flexible sort par le haut.

    Ludovic - Réponse

  9. Installation de RAM dans le Mac mini modèle A1176: étape 9, image 1 de 1
    • Tirez le câble-ruban de la carte audio hors de sa prise.

    • S'il reste bloqué, cela signifie que le dispositif de verrouillage du câble ZIF n'est pas complètement déverrouillé. Assurez-vous qu'il est relevé sur toute sa largeur d'1 mm par rapport à la prise sur la carte d'interconnexion.

    As an option to avoid potential damage when disconnecting the cable from the ZIF socket and clip, it is possible to unscrew the audio board and remove it along with the internal frame.

    Nick Baldwin - Réponse

  10. Installation de RAM dans le Mac mini modèle A1176: étape 10, image 1 de 2 Installation de RAM dans le Mac mini modèle A1176: étape 10, image 2 de 2
    • Faites pivoter le mini de sorte que le mécanisme de chargement de l'emplacement du SuperDrive se trouve face à vous.

    • À l'aide d'une pince, soulevez le connecteur du câble du capteur thermique du disque dur hors de sa prise sur la carte mère.

    • À l'aide de la pince, saisissez le connecteur (comme illustré), mais pas les fils.

    • Le connecteur se trouve sous l'ouverture du lecteur optique, à côté de la batterie PRAM.

    Managed to leave this connected by flopping back the drive rather than totally removing

    pglock - Réponse

    WATCH OUT!!

    separated one of the wires from the connector very easily. i would have preferred to use a spudger at this step. the tweezers in effect snipped the wire!!

    mklsvg - Réponse

    As my experience you should definitely use angeled tweezers as shown in several pictures. To avoid stripped cable deflash sharp edges of the tweezers a little bit. I never experienced problems when using that kind of tool carefully.

    Timpetou - Réponse

    I've had to remove a few of these connectors on iBooks and other small Apple devices ... I've found that, with careful and gentle pressure (working first one side and then the other) using a small flat-headed jeweller's screwdriver is best.

    Mike Haines - Réponse

    I agree Mike.

    dixieskettlecorn -

    Note where the airport antennae connecting wire comes out from the interior along the top. When reassembling, it has to be routed the same way, or it won't reach its install position.

    robert - Réponse

    If your fan runs at high speed after you complete this project, you have forgotten to reconnect the thermal sensor.

    Curt - Réponse

  11. Installation de RAM dans le Mac mini modèle A1176: étape 11, image 1 de 2 Installation de RAM dans le Mac mini modèle A1176: étape 11, image 2 de 2
    • Au cours des prochaines étapes, vous allez retirer les quatre vis Phillips par lesquelles le cadre intérieur est fixé au boîtier inférieur. Pour chaque étape, vous disposerez d'une vue d'ensemble indiquant la configuration générale et d'une vue rapprochée de la vis concernée.

    • Retirez la vis Phillips cruciforme près du bouton de mise sous tension par laquelle le cadre intérieur est fixé au boîtier inférieur.

  12. Installation de RAM dans le Mac mini modèle A1176: étape 12, image 1 de 2 Installation de RAM dans le Mac mini modèle A1176: étape 12, image 2 de 2
    • Retirez la vis Phillips cruciforme près du témoin de veille par laquelle le cadre intérieur est fixé au boîtier inférieur.

    • Cette vis est la plus longue des quatre vis par lesquelles le cadre intérieur est fixé au boîtier inférieur.

  13. Installation de RAM dans le Mac mini modèle A1176: étape 13, image 1 de 2 Installation de RAM dans le Mac mini modèle A1176: étape 13, image 2 de 2
    • Retirez la vis Phillips du cadre intérieur près de l'antenne Bluetooth.

    Before removing any of these screws, there is another step needed which is not here:

    On the front of the optical drive, right side as you look at the slot-load, is a small blue board attached by a single black screw. This needs to be removed before the optical drive can be taken out.

    Mike Haines - Réponse

  14. Installation de RAM dans le Mac mini modèle A1176: étape 14, image 1 de 2 Installation de RAM dans le Mac mini modèle A1176: étape 14, image 2 de 2
    • Retirez la vis Phillips cruciforme près des ports audio par laquelle le cadre intérieur est fixé au boîtier inférieur.

    On reassembly, if you don't have a magnetic screwdriver, a tiny dab of grease at the tip of your screwdriver will help hold the screw on the driver so you can lower it into the recessed slot.

    pfbloom - Réponse

  15. Installation de RAM dans le Mac mini modèle A1176: étape 15, image 1 de 2 Installation de RAM dans le Mac mini modèle A1176: étape 15, image 2 de 2
    • Soulevez doucement le cadre intérieur hors du boîtier inférieur, en faisant attention à l'antenne AirPort et aux câbles qui peuvent se coincer.

    • Vous serez peut-être obligé de tirer le cadre intérieur vers le haut près de la carte d'interconnexion pour le séparer de la carte mère.

    At this point be careful that you don't pull out the Airport antenna ... but if you do, just check that it is back before re-assembling.

    Mike Haines - Réponse

    During re-assembly, the internal frame has to go in at an angle ... the back of the optical drive goes in first.

    This means that you can seat the fan cover correctly, but more importantly, there is an interconnect board on the back of the optical drive that must be firmly pushed back into its housing on the logic board.

    Mike Haines - Réponse

    Reassembly: Before slipping the main frame back into its place, refer to earlier photos, ensuring proper routing of the WiFi cable.

    Steve - Réponse

    If, like me, you pull the wire on the airport antenna free, it snaps back into place easily. The connector is on the extra card screwed to the motherboard that looks like it has a phone battery embedded in it. The connector is at the top of the 'battery'. This accessory card is the wifi card, so it makes sense that the antenna plugs onto this.

    Dan - Réponse

  16. Installation de RAM dans le Mac mini modèle A1176, Installation de RAM dans le Mac mini modèle A1176: étape 16, image 1 de 2 Installation de RAM dans le Mac mini modèle A1176, Installation de RAM dans le Mac mini modèle A1176: étape 16, image 2 de 2
    • Écartez les deux clips de chaque côté de la barrette de RAM simultanément pour libérer cette dernière. Ces clips maintiennent la barrette en place et lorsque vous les écartez, la barrette se débloque.

  17. Installation de RAM dans le Mac mini modèle A1176: étape 17, image 1 de 1
    • Tirez la barrette de RAM hors de son connecteur.

    • Si deux barrettes de RAM sont installées, répétez la procédure ci-dessus pour la seconde barrette.

    When (re)inserting RAM, the connector is tight - push firmly on both sides evenly - usually will "click" when fully seated. Look at the RAM connector edge - the gold should be almost completely within the socket (if not fully seated, it won't be recognized).

    robert - Réponse

Conclusion

Pour remonter votre appareil, suivez les mêmes instructions dans l'ordre inverse.

307 autres ont terminé cette réparation.

Merci à ces traducteurs :

en fr

100%

Fabienne Detoc nous aide à réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›

19 commentaires

As a quick warning for noobs (that'd be me before I attempted this repair :P ), you need a matching pair of RAM (two chips the same size and spec). Otherwise, the computer won't boot up. ^_^

Skylar MacDonald - Réponse

There were 2x 1GB chips in my 2007 mini. I bought 1x 2GB chip, because I read somewhere that model only would allow 3GB. After replacing a 1GB chip with the new 2GB chip, the system is only showing 1GB RAM installed. Is this what you’re talking about? If I buy another 2GB chip, will it work? PC2-5300 2 GB RAM Chip

Jeff Box -

That is not always true. Often, perhaps…60/40, ish? My 2007 mac mini 2,1 is running one 1gb stick and one 2gb stick, a 500gb Kingston SSD and a salvaged superdrive from a MBP. I am tempted to try a core 2 quad or Xeon in it. For no particular reason than to see if it runs. anyone tried that one? I also had a 2008 mac pro 3,1 running four 2gb and four 4gb of under spec ram without issues.

In the 25 years i’ve been hanging out in server rooms, the client side of the working guidelines for ram matching has become less strict., but still, I believe, the ability to mix is in the manufacturing process. there’s no way but experience to be able to confirm that different makes, speed or size will function together. Unless of course stated in manufacturers documentation. The quality of the individual components will decide.

It will either work or it wont.

If you don’t have ram laying about, then your 100% right, buy matching pairs. otherwise, try it 'till it fires!

Stu Blair -

I successfully run 3GB in my A1176 Minis. When I put the 2GB chip in the bottom slot with the 1GB chip in the top slot, the machine would not boot and the power LED would blink continuously. When I put the 1GB chip in the bottom slot with the 2GB chip in the top slot, the machine works perfectly and sees all 3GB of RAM. (I don’t know if this is a rule or not, this is strictly my anecdotal experience.) I have *not* experienced installing 3GB and having the Mini run and only report 1GB. If you do that, I’d recommend checking to assure that the 2GB stick is seated properly.

I’ve also used 4GB without any trouble in A1176 Minis, but this model can only address a maximum of 3GB RAM. I have run performance comparisons between one equipped with 4GB and equipped with 3GB RAM and they measured identically. If you’re upgrading an A1176 from 2GB (equipped with a pair of 1GB chips) to 3GB, you can save a few dollars by just buying a single PC2-5300 2GB stick.

Mark B -

Thanks a lot, 1Gb -> 4Gb is done !

Eric Seigne - Réponse

This was easier than it looked, the only thing I had trouble with was getting the cover off (tried to use a flexible palette knife, bad idea) and getting the little sensor plug back in (it's SO tiny.) Oh, and one screw I had trouble getting back into the hidden recessed hole because my screwdriver isn't magnetized.

Speaking of which, size of screwdriver matters, I bought a set with a size 0 and size 000, but no 00, neither worked. Fortunately I had one of those cheap eyeglass repair kits, and the Phillips screwdriver worked perfectly.

Alexa - Réponse

The covers are the Worst….then and Now!!!

Stu Blair -

Thank you so much iFixit! Very nice guide. Followed and worked like a charm. Keep up the good info coming!

Eddie Abner - Réponse

Great step-by-step instructions, but now it won't boot... What to do?

John Nichols - Réponse

did you change ram

john korteman -

Great job, went like a charm. btw, the old Mac mini 2007 can accept 4 Gb, and it looks like it uses the full monthly according to the memory app I am using.

Some say t can't but how can I make sure of that, does any one knows?

Went from 2 towards 4 Gb, now my old iMac from the same year is most lightly the same hardware as this Mini and that one can hold 4 to 6 Gb.

Grts

The Mac Fiddler

Zathros - Réponse

Instructions along with comments worked well. Thank you. Tab of silicon grease very helpful on reassembly.

paulrbusch - Réponse

Excellent! Thanks a million! :-)

Sven Bornemark - Réponse

This update worked very well. Tougher to get apart than expected. My experience was that the prying tool is very flexible and bends. You are trying to find and push the plastic hooks inward slightly to release them rather than prying on the back housing. Also be careful with the Airport antena - it can pop off the connector from the interior pc-board. I didn’t find this out until I went to re-attach it and found he wire had popped free and I had to take out all the screws and and connectors and disassemble a second time to re-connect it! Fortunately ifixit has instructions on where that goes, thanks!

Will Snow - Réponse

that is so right. the prying is not good. the tabs, especially on a ten or more years old device, are brittle and the intake vents don’t leave much for them to be mounted on. I have broken a couple, when I was a Mac mini virgin.

there’s always that one screw/bolt/nut that gives you the gears. cars, macs, anything mechanical always has that one @#!@#@ fastener.

Stu Blair -

Thank you, it has worked very good!

Michael Westeroth - Réponse

Thank you! Works very well!

Michael Westeroth - Réponse

I found a pizza cutter is the best tool to separate cover from the bottom part.

Marcin Pancewicz - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 4

7 derniers jours : 35

30 derniers jours : 130

Total : 189,631