Réparez vos affaires Communauté Boutique

Ivation IVWPDC20Y Flash Bulb Replacement

Introduction

Use this guide to replace the bulb on the flash if it is burnt out.

Ce dont vous avez besoin

  1. Ivation IVWPDC20Y Flash Bulb Replacement, Flash Bulb: étape 1, image 1 de 1

    • With the H2.0 bit screwdriver, remove the two screws on the yellow waterproof cover

    Modifier

  2. Ivation IVWPDC20Y Flash Bulb Replacement: étape 2, image 1 de 1

    • Apply a plastic opening tool to each of the corners and gently remove the casing

    • The front casing is held down by adhesive and may require additional work to remove

    • Apply just enough force to undo the inner latches to make sure not to damage the waterproof seal

    Modifier

  3. Ivation IVWPDC20Y Flash Bulb Replacement: étape 3, image 1 de 1

    • Remove the five silver screws from the inner casing using the PH00 screwdriver bit

    Modifier

  4. Ivation IVWPDC20Y Flash Bulb Replacement: étape 4, image 1 de 1

    • Remove the six screws from the edge of the clear inner casing with the PH00 screwdriver bit

    • These screws are very small and easy to strip so apply consistent pressure when removing them

    Modifier

  6. Ivation IVWPDC20Y Flash Bulb Replacement: étape 5, image 1 de 1

    • Pry off back outer casing using the black spudger or the blue prying tools

    Modifier

  7. Ivation IVWPDC20Y Flash Bulb Replacement: étape 6, image 1 de 1

    • Carefully remove the screen from the silver casing using a prying tool or the black spudger

    • There is adhesive in the center of the screen, be sure not to bend it when applying pressure

    Modifier

  8. Ivation IVWPDC20Y Flash Bulb Replacement: étape 7, image 1 de 1

    • Gently push out the pins holding the orange tape down using the pointy end of the spudger

    • Screen and orange tape should slip out as a whole

    Modifier

  9. Ivation IVWPDC20Y Flash Bulb Replacement: étape 8, image 1 de 1

    • Remove three screws holding the silver screen casing to the motherboard using the PH00 bit screwdriver

    Modifier

  10. Ivation IVWPDC20Y Flash Bulb Replacement: étape 9, image 1 de 1

    • Remove three screws holding the motherboard into the casing using the PH00 bit screwdriver bit

    Modifier

  11. Ivation IVWPDC20Y Flash Bulb Replacement: étape 10, image 1 de 1

    • Gently lift the corner of the motherboard out

    • Everything should come out as one component free of the casing

    Modifier

  12. Ivation IVWPDC20Y Flash Bulb Replacement: étape 11, image 1 de 1

    • Remove the soldering on the three wires holding the flash bulb

    • The wires are different colors: red, white, and black

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 3 autres contributeurs

Wendy Jones

Membre depuis le 02/06/16

225 Réputation

2 tutoriels rédigés

Badges: 10

+ 7 badges supplémentaires

Équipe

USF Tampa, Team 6-6, Eyestone Spring 2016 Membre de l'équipe USF Tampa, Team 6-6, Eyestone Spring 2016

USFT-EYESTONE-S16S6G6

3 membres

5 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 243