Aller au contenu principal

Ce tutoriel a des changements plus récents. Passer à la dernière version non vérifiée.

JBL Pulse 2 Motherboard Replacement

Ce dont vous avez besoin

  1. JBL Pulse 2 Motherboard Replacement, Battery: étape 1, image 1 de 2 JBL Pulse 2 Motherboard Replacement, Battery: étape 1, image 2 de 2
    • Remove the rubber rings from either end of the device.

    • If there is difficulty in lifting the rings from the device, use the metal spudger.

  2. JBL Pulse 2 Motherboard Replacement: étape 2, image 1 de 1
    • Remove the four 4.8mm Phillips #1 screws from each end of the device with the Phillips head screwdriver.

    • Lift the end pieces off of the device.

  3. JBL Pulse 2 Motherboard Replacement: étape 3, image 1 de 1
    • Remove the four 9.5mm Phillips #1 screws from each end of the device.

  4. JBL Pulse 2 Motherboard Replacement: étape 4, image 1 de 2 JBL Pulse 2 Motherboard Replacement: étape 4, image 2 de 2
    • Peel one end off and slowly draw it across the length of the device until you get to the other side.

  5. JBL Pulse 2 Motherboard Replacement: étape 5, image 1 de 3 JBL Pulse 2 Motherboard Replacement: étape 5, image 2 de 3 JBL Pulse 2 Motherboard Replacement: étape 5, image 3 de 3
    • Remove the four 7.9mm Phillips #1 screws along the black centerpiece of the device between the camera and the auxiliary port.

    • Lift up the casing and circuit board but do not try and remove the ribbon wires.

  6. JBL Pulse 2 Motherboard Replacement: étape 6, image 1 de 1
    • Remove the cover from the end that the ribbon wires are attached to. It should peel off easily.

  7. JBL Pulse 2 Motherboard Replacement: étape 7, image 1 de 2 JBL Pulse 2 Motherboard Replacement: étape 7, image 2 de 2
    • Unlatch the mechanism holding the ribbon wires in place, then disconnect them from the motherboard.

    • To access the wires, remove some of the black glue holding them in place with the spudger.

  8. JBL Pulse 2 Motherboard Replacement: étape 8, image 1 de 2 JBL Pulse 2 Motherboard Replacement: étape 8, image 2 de 2
    • Slowly pull the ribbon wires out from the outside.

    • If there is too much resistance, remove more of the black glue.

  9. JBL Pulse 2 Motherboard Replacement: étape 9, image 1 de 2 JBL Pulse 2 Motherboard Replacement: étape 9, image 2 de 2
    • Remove the four 7.9mm Phillips #1 screws around the edges of the center piece.

    • Slide the outer casing off away from the auxiliary and micro USB port.

  10. JBL Pulse 2 Motherboard Replacement: étape 10, image 1 de 1
    • Remove the other end of the device to access the wiring underneath it.

  11. JBL Pulse 2 Motherboard Replacement: étape 11, image 1 de 1
    • Use the angled tweezers to disconnect the battery from the motherboard. It will take some work to remove this piece.

  12. JBL Pulse 2 Motherboard Replacement: étape 12, image 1 de 1
    • Remove the four 7.9mm Phillips #1 screws from the black centerpiece of the device.

  13. JBL Pulse 2 Motherboard Replacement: étape 13, image 1 de 2 JBL Pulse 2 Motherboard Replacement: étape 13, image 2 de 2
    • Use the spudger to reach under the sides of the black centerpiece to access the six latches, three of which are on each side.

  14. JBL Pulse 2 Motherboard Replacement: étape 14, image 1 de 2 JBL Pulse 2 Motherboard Replacement: étape 14, image 2 de 2
    • Lift the black centerpiece off with the metal spudger to reveal the battery underneath.

  15. JBL Pulse 2 Motherboard Replacement: étape 15, image 1 de 1
    • Use a hot air gun to soften the hot glue in order to fully remove the battery.

  16. JBL Pulse 2 Motherboard Replacement, Motherboard: étape 16, image 1 de 3 JBL Pulse 2 Motherboard Replacement, Motherboard: étape 16, image 2 de 3 JBL Pulse 2 Motherboard Replacement, Motherboard: étape 16, image 3 de 3
    • Manually remove the LED strips from the outside of the white plastic casing.

  17. JBL Pulse 2 Motherboard Replacement: étape 17, image 1 de 3 JBL Pulse 2 Motherboard Replacement: étape 17, image 2 de 3 JBL Pulse 2 Motherboard Replacement: étape 17, image 3 de 3
    • Use the Phillips #1 screwdriver to remove the ten 9.5mm screws that hold the cage in place.

    • Lift the cage off.

  18. JBL Pulse 2 Motherboard Replacement: étape 18, image 1 de 2 JBL Pulse 2 Motherboard Replacement: étape 18, image 2 de 2
    • Use the Phillips #1 screwdriver to remove the eight 6.4mm screws that hold the speakers in place.

    • Partially remove the speakers so you can see where they connect to the motherboard.

  19. JBL Pulse 2 Motherboard Replacement: étape 19, image 1 de 2 JBL Pulse 2 Motherboard Replacement: étape 19, image 2 de 2
    • Use the straight tweezers to disconnect the speakers from the motherboard.

    • Fully remove the speakers once they are disconnected from the motherboard.

  20. JBL Pulse 2 Motherboard Replacement: étape 20, image 1 de 1
    • Disconnect the remaining wires from the motherboard with the straight tweezers.

    • Be cautious when performing this step. The mic wire is fragile and liable to break.

  21. JBL Pulse 2 Motherboard Replacement: étape 21, image 1 de 1
    • Use a hot air gun to soften the glue from the corners of the motherboard.

    • Slide the motherboard out of the casing.

    • The hot glue covers portions of the motherboard so be careful when softening and removing it.

Conclusion

To reassemble your device, follow these instructions in reverse order.

3 autres ont terminé cette réparation.

Emilee Hicks

Membre depuis le 08/31/18

779 Réputation

3 tutoriels rédigés

Équipe

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 19

Total : 2,153