Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Boutique

Introduction

This guide will help walk you through the steps of replacing the needle of a Keurig Mini. To get into the device all you will need is a #1 Philips screw driver.

Pièces

Aucune pièce spécifiée.

  1. Press on tab while pulling up on K-cup until you hear a click. Repeat for the remaining tabs. We found using the smallest of the "plastic opening tools" worked wonders. Press on tab while pulling up on K-cup until you hear a click. Repeat for the remaining tabs. We found using the smallest of the "plastic opening tools" worked wonders. Press on tab while pulling up on K-cup until you hear a click. Repeat for the remaining tabs. We found using the smallest of the "plastic opening tools" worked wonders.
    • Press on tab while pulling up on K-cup until you hear a click. Repeat for the remaining tabs. We found using the smallest of the "plastic opening tools" worked wonders.

  2. Once all of the tabs have been pressed, the K-Cup should just pop out. After, you just pull the remainder of the K-Cup. You have successfully removed the K-Cup. Once all of the tabs have been pressed, the K-Cup should just pop out. After, you just pull the remainder of the K-Cup. You have successfully removed the K-Cup.
    • Once all of the tabs have been pressed, the K-Cup should just pop out. After, you just pull the remainder of the K-Cup. You have successfully removed the K-Cup.

  3. Remove two 9 mm Phillips #1 screws. Avoid the top needle if at all possible. The needle may cut you and/or penetrate your skin.
    • Remove two 9 mm Phillips #1 screws.

    • Avoid the top needle if at all possible. The needle may cut you and/or penetrate your skin.

    • The screws are located on the top of where the K-Cup would be.

    you show two screws I have 2 more deeper in how do you remove them?

    wevie100 - Réponse

  4. Once you remove the screws, the top cover should come out. You will then want to remove these screws which are the same size. The needle is sharp, so be careful.
    • Once you remove the screws, the top cover should come out.

    • You will then want to remove these screws which are the same size.

    • The needle is sharp, so be careful.

    On my model k10, these screws are actually slightly larger than those on step #3. So it is best to still separate them, just incase. Happy repairing~

    Bernard Dolecki - Réponse

    The top cover didn’t come off easily on mine. Once I removed the 2 screws I had to slowly lift it up from the front until it popped off. It looks like there might have been a small glue spot at the back center of the plastic edge.

    jkempinger - Réponse

  5. Once you get those removed, you are going to want to pull on the hose until it pops off.
    • Once you get those removed, you are going to want to pull on the hose until it pops off.

    • Once the hose comes off, the needle will fall out by itself.

    • Be careful when picking up the needle as the needle is sharp.

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Mark Henein

Membre depuis le 04/02/2016

369 Réputation

2 tutoriels rédigés

Équipe

USF Tampa, Team 17-6, Blackwell Winter 2016 Membre de l'équipe USF Tampa, Team 17-6, Blackwell Winter 2016

USFT-BLACKWELL-W16S17G6

2 membres

2 tutoriels rédigés

Where do you buy the needle I know you can get the exit needle with the holder, but can’t find this one.

tbushwacker - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 1

7 derniers jours : 6

30 derniers jours : 49

Total : 3,628