Aller au contenu principal

Introduction

The motherboard may need replacing for a multitude of reasons. Perhaps the phone underwent severe water damage and hasn't worked the same since. Or maybe the touchscreen still isn't functional even after it's been replaced. Whatever the reason, this guide will help you get to and replace the motherboard.

Pièces

Aucune pièce spécifiée.

  1. Press down on the back of the phone, applying moderate pressure. Slide the back casing down to separate it.
    • Press down on the back of the phone, applying moderate pressure.

    • Slide the back casing down to separate it.

  2. Remove the back casing to expose the battery. Use a plastic spudger to lift the battery out using the battery's groove on its top left corner.
    • Remove the back casing to expose the battery.

    • Use a plastic spudger to lift the battery out using the battery's groove on its top left corner.

  3. Remove the six 3.18 mm screws using a Phillips 00 screwdriver. Remove the six 3.18 mm screws using a Phillips 00 screwdriver.
    • Remove the six 3.18 mm screws using a Phillips 00 screwdriver.

  4. Insert the flat end of the spudger between the front and back panels, and pry it apart by running the spudger along the side to further separate them. Go all the way around, prying as you go, until the back casing completely separates from the rest of the phone.
    • Insert the flat end of the spudger between the front and back panels, and pry it apart by running the spudger along the side to further separate them.

    • Go all the way around, prying as you go, until the back casing completely separates from the rest of the phone.

  5. Unclip the two flex cables -- a small one located on the left side on the lower half of the motherboard, and a longer one on the right side, higher up. Unclip the two flex cables -- a small one located on the left side on the lower half of the motherboard, and a longer one on the right side, higher up. Unclip the two flex cables -- a small one located on the left side on the lower half of the motherboard, and a longer one on the right side, higher up.
    • Unclip the two flex cables -- a small one located on the left side on the lower half of the motherboard, and a longer one on the right side, higher up.

  6. Pry out the earpiece speaker using the spudger. Pry out the vibration motor using the spudger. Pry out the vibration motor using the spudger.
    • Pry out the earpiece speaker using the spudger.

    • Pry out the vibration motor using the spudger.

  7. Place the flat end of the spudger underneath the digitizer connector and pry it up to disconnect it. Place the flat end of the spudger underneath the digitizer connector and pry it up to disconnect it.
    • Place the flat end of the spudger underneath the digitizer connector and pry it up to disconnect it.

  8. Remove the sticker to uncover the screws underneath. Remove the six 1.59 mm screws using a Phillips 00 screwdriver. Remove the six 1.59 mm screws using a Phillips 00 screwdriver.
    • Remove the sticker to uncover the screws underneath.

    • Remove the six 1.59 mm screws using a Phillips 00 screwdriver.

  9. Lift the bottom portion of the motherboard away from the front panel. Do not forcefully pull the components apart as there is another connector on the underside of the motherboard attaching it to the panel. Insert the flat end of the spudger in between the panel and motherboard to unfasten the connector.
    • Lift the bottom portion of the motherboard away from the front panel.

    • Do not forcefully pull the components apart as there is another connector on the underside of the motherboard attaching it to the panel.

    • Insert the flat end of the spudger in between the panel and motherboard to unfasten the connector.

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autres ont terminé cette réparation.

Scott Nguyen

Membre depuis le 16/09/2015

522 Réputation

3 tutoriels rédigés

Équipe

USF Sarasota-Manatee, Team 1-2, Stewart Fall 2015 Membre de l'équipe USF Sarasota-Manatee, Team 1-2, Stewart Fall 2015

USFSM-STEWART-F15S1G2

5 membres

16 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 228