Introduction

The LCD portion of the screen is what actually creates the image on the phone. The digitizer is contained in the glass panel on the front of the phone, and is what detects the user's touch.

Pry the back cover off of the phone with your fingernail. There is a notch located at the bottom of the phone for improved leverage.
  • Pry the back cover off of the phone with your fingernail. There is a notch located at the bottom of the phone for improved leverage.

Ajouter un commentaire

The battery is the large black rectangle towards the bottom half of the phone.
  • The battery is the large black rectangle towards the bottom half of the phone.

  • There is a semi-circular notch at the bottom edge of the battery. Press against and up on the battery to pop it out.

Ajouter un commentaire

  • Remove 9 screws from the phone. The locations of these screws are circled in the picture.

  • 5.5mm length PH00 screws

  • 4mm length PH00 screws

Ajouter un commentaire

  • Gently pull down on the bottom cover to remove it.

Ajouter un commentaire

  • Using a plastic opening tool, gently pry around the perimeter of the device.

  • The ribbons behind the buttons and ports are very delicate. Make sure you do not run your plastic opening tool too deep into the bezel, as you could damage them.

  • The button covers rest under the Mid-Cover Bezel. Remove them and set aside.

I think they want you to refer to the blue tool as the "plastic opening tool."

Dan Brown - Réponse

  • Using a spudger or plastic opening tool, gently disconnect the ribbon cable attached to the black SIM card board.

Ajouter un commentaire

  • Use a hair-dryer on high, or a heat-gun on low to heat the device and loosen the adhesive which holds down the SD/SIM Card Board.

  • Evenly heat the device in short intervals for about one minute.

  • Do not heat the device for more than 30 seconds at a time to prevent over-heating.

You could also use the iOpener tool for this step. What is that the adhesive is holding in place?

Dan Brown - Réponse

  • Gently pry the board up to release it from the now soft adhesive. Make sure you pry up the little tab connected to the camera unit as well.

  • If the board is too difficult to separate than more heating may be required.

Ajouter un commentaire

  • Using a spudger or plastic opening tool, gently lift the ribbon cables connected to the motherboard.

  • The button tabs, highlighted in orange, are held in with a light adhesive. Gently lift them out of the body of the phone with a spudger.

Ajouter un commentaire

  • Remove the antenna cable by disconnecting both ends.

  • One end connects to the motherboard and the other connects near bottom of the phone.

Ajouter un commentaire

  • Using a spudger gently lift the motherboard assembly out of the case.

  • Make sure the motherboard does not get snagged on the camera's ribbon cable.

Ajouter un commentaire

  • Using the plastic opening tool disconnect the ribbon cable connected to the headphone jack assembly.

Ajouter un commentaire

  • Separate the Headphone Jack from the body of the phone. It should pop off relatively easily.

Ajouter un commentaire

  • Using a pry tool, carefully remove the front bezel of the phone.

  • There are many clips holding it together, so take your time and be patient.

  • Do not poke too far into the phone while prying, as you may damage the LCD from the side.

Ajouter un commentaire

  • There is a ribbon cable coming from the front portion of the phone that fits through a slot in the back.

  • Pull this ribbon cable through the slot to fully separate the halves.

Ajouter un commentaire

  • Gently pry the LCD from the phone half.

  • Don't touch the front of the LCD panel or the back of the digitizer (the clear panel).

  • If the glass on your phone is broken, be careful to avoid getting cut by any shards that may fall apart.

Ajouter un commentaire

  • When you are putting the front and back portions of the phone back together, make sure you don't forget to pull the LCD ribbon cable through the corresponding slot to connect back to the motherboard.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Dale Pearson

Membre depuis le 22/09/2014

775 Réputation

6 tutoriels rédigés

Équipe

USF Tampa, Team 10-6, Brown Fall 2014 Membre de l'équipe USF Tampa, Team 10-6, Brown Fall 2014

USFT-BROWN-F14S10G6

3 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 18

Total : 769