Lenovo Legion 5 17ACH6H RAM Replacement

Introduction

This guide is for replacing both RAM modules for the Lenovo Legion 5 17ACH6H laptop. According to the laptop's manual, the laptop supports up to 16 GB DDR4 - 3200, dual channel RAM. However, this laptop can run 32 GB of RAM. You can choose a different RAM module brand as long as it meets the laptop's RAM specifications.

Before opening the laptop, ensure this does not void its warranty. Opening without damaging the parts won't void the warranty in the United States, but this may vary with region and seller.

Before replacing any part of this laptop, ensure it is completely powered off and not connected to power. It is also important that the laptop is not in sleep or hibernation mode.

Ce dont vous avez besoin

Étape 1 RAM

Lenovo Legion 5 17ACH6H RAM Replacement, RAM: étape 1, image 1 de 3

Lenovo Legion 5 17ACH6H RAM Replacement, RAM: étape 1, image 2 de 3

Lenovo Legion 5 17ACH6H RAM Replacement, RAM: étape 1, image 3 de 3

Use the Phillips #1 screwdriver to remove the ten screws on the back panel.
Four 4.6 mm PH1 screws
Six 12.8 mm PH1 screws

Modifier

Étape 2

Lenovo Legion 5 17ACH6H RAM Replacement: étape 2, image 3 de 3

Insert the rounded side of the opening pick on the lower right of the back panel.
Apply light pressure downwards to release the clip.
Slide the opening pick along the lower back side of the panel to release the remaining clips.

Modifier

Étape 3

Lenovo Legion 5 17ACH6H RAM Replacement: étape 3, image 3 de 3

Insert the opening pick on the right side of the panel (along the ports) and slide it across to release the pins.
Repeat this step on the left side of the panel.

Modifier

Étape 4

Lenovo Legion 5 17ACH6H RAM Replacement: étape 4, image 3 de 3

Slide the pick in the vent near the USB C port.
Rotate the pick so it is on the top part of the vent.
Slide the pick across the top side of the vent
The laptop can be held vertically, so the process is much easier.
Repeat this step on the other side vent near the USB A port.

Modifier

Étape 5

Lenovo Legion 5 17ACH6H RAM Replacement: étape 5, image 3 de 3

Grab the back panel and lift it to remove it from the chassis.
Before completely lifting the back panel, the panel should be pushed a little bit away from you. This is to prevent the panel from getting stuck with the IO ports.

Modifier

Étape 6

Lenovo Legion 5 17ACH6H RAM Replacement: étape 6, image 3 de 3

Use the pointed tip of a spudger to carefully push on each side of the connector.
Use the flat side of the spudger at the top of the battery connector to completely push it out.
Pull the cable by the connector and not the wires to move it out of the way.
It is important to disconnect the battery since touching the components with the battery connected can short-circuit the device. This could cause damage to the components and yourself.

Modifier

Étape 7

Lenovo Legion 5 17ACH6H RAM Replacement: étape 7, image 3 de 3

Place the flat side of the spudger between the RAM shield (right) and the metal plate (left) at a 45-degree angle.
Pry open the bottom part of the metal plate by moving the spudger toward the RAM shield.

Modifier

Étape 8

Lenovo Legion 5 17ACH6H RAM Replacement: étape 8, image 3 de 3

Place the flat side of the spudger between the fan (right) and the metal plate (left).
Pry open the top part of the metal plate by moving the spudger toward the fan.

Modifier

Étape 9

Lenovo Legion 5 17ACH6H RAM Replacement: étape 9, image 3 de 3

Grab both sides of the metal plate to lift it off the clips.

Modifier

Étape 10

Lenovo Legion 5 17ACH6H RAM Replacement: étape 10, image 3 de 3

With both thumbs, push the clips outward.
Gently slide the RAM module out of the socket to remove it.

Modifier

Étape 11

Lenovo Legion 5 17ACH6H RAM Replacement: étape 11, image 3 de 3

Repeat step 10 to remove the top module.
The laptop was rotated 180 degrees, which is why it is facing the camera.

Modifier

Étape 12

Lenovo Legion 5 17ACH6H RAM Replacement: étape 12, image 3 de 3

Insert the RAM module at a 45-degree angle.
Make sure the module aligns with the slot. You can check by making sure the module pins' holes align with the slot.
With a finger on the top part of the module, push the RAM stick downward.
A click indicates that the module has been inserted successfully.