Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Pièces & Outils

Introduction

This simple guide will show you how to unscrew and remove all cables from the motherboard of a Lenovo Yoga 710-14KB besides the display cable, which will need to be unsoldered.

  1. Ensure your device is completely OFF before starting this guide.
    • Ensure your device is completely OFF before starting this guide.

    • Use a Torx T4 screwdriver to unscrew the nine 5 mm screws holding the cover in place.

    • Use a Torx T4 screwdriver to unscrew the 8 mm screw in the center.

    • When, reassembling, make sure not to tighten the screws too much or you may risk cracking the plastic cover.

  2. Use the plastic opening tool to pry the cover up and away from the laptop, starting at one end and working your way around the cover. The cover is large and flat and made of thin plastic. It cracks easily, so make sure not to pry too hard. The cover is large and flat and made of thin plastic. It cracks easily, so make sure not to pry too hard.
    • Use the plastic opening tool to pry the cover up and away from the laptop, starting at one end and working your way around the cover.

    • The cover is large and flat and made of thin plastic. It cracks easily, so make sure not to pry too hard.

  3. Use a Phillips #00 screwdriver to remove the four 3 mm screws holding the battery in place. Be careful not to cross-thread the screws. Also, don't let the screws fall down into the laptop case.
    • Use a Phillips #00 screwdriver to remove the four 3 mm screws holding the battery in place.

    • Be careful not to cross-thread the screws. Also, don't let the screws fall down into the laptop case.

  4. Fix Kits pour écrans LCD d'iPhone

    L'option économique couverte par notre garantie à vie.

    Acheter des kits

    Fix Kits pour écrans LCD d'iPhone

    Réduisez les coûts de réparation et non pas la qualité.

    Acheter des kits
  5. Lift the battery connector straight up away from the board using your fingers or an opening tool. Lift the battery connector straight up away from the board using your fingers or an opening tool.
    • Lift the battery connector straight up away from the board using your fingers or an opening tool.

  6. Remove the battery.
    • Remove the battery.

  7. Use a Phillips #00 screwdriver to remove the 3mm screw on the SSD. Use a Phillips #00 screwdriver to remove the 3mm screw on the SSD.
    • Use a Phillips #00 screwdriver to remove the 3mm screw on the SSD.

  8. Use your fingers to lift up the SSD and pull away from the socket removing it from the laptop. Use your fingers to lift up the SSD and pull away from the socket removing it from the laptop.
    • Use your fingers to lift up the SSD and pull away from the socket removing it from the laptop.

  9. Use a PH00 screwdriver to remove the nine 3mm screws.
    • Use a PH00 screwdriver to remove the nine 3mm screws.

  10. Disconnect the indicated cables from the motherboard. Be careful when removing cables. Do not pull or yank cables from their slots.
    • Disconnect the indicated cables from the motherboard.

    • Be careful when removing cables. Do not pull or yank cables from their slots.

    • Remove the motherboard.

    • If you want to fully remove the motherboard, you must desolder the display cable.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Evan Cruzen

Membre depuis le 01/11/2018

205 Réputation

2 tutoriels rédigés

Équipe

UMass Dartmouth, Team S5-G8, Gulbrandsen Fall 2018 Membre de l'équipe UMass Dartmouth, Team S5-G8, Gulbrandsen Fall 2018

UMASSD-GULBRANDSEN-F18S5G8

3 membres

4 tutoriels rédigés

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 3

7 derniers jours : 17

30 derniers jours : 57

Total : 930