Réparez vos affaires Communauté Boutique

Lubricate General Electric Telephone 2-9710A Tuning Slider

Introduction

This guide will show how to lubricate the volume slider after you have opened up the base of the phone. Your volume slider will operate smooth after completing this guide.

Ce dont vous avez besoin

  1. Lubricate General Electric Telephone 2-9710A Tuning Slider, Phone Cord: étape 1, image 1 de 2 Lubricate General Electric Telephone 2-9710A Tuning Slider, Phone Cord: étape 1, image 2 de 2

    • Unplug the device before proceeding.

    • Using a plastic opening tool, remove the phone cord from the phone jack at the base of the headset.

    • To release the cable, gently press down on the top plastic tab of the connector.

    Traduire

  2. Lubricate General Electric Telephone 2-9710A Tuning Slider: étape 2, image 1 de 3 Lubricate General Electric Telephone 2-9710A Tuning Slider: étape 2, image 2 de 3 Lubricate General Electric Telephone 2-9710A Tuning Slider: étape 2, image 3 de 3

    • Remove the 7.5 mm screw.

    • Remove the screw cap.

    • Pull up the phone cord to remove it from the base.

    Traduire

  3. Lubricate General Electric Telephone 2-9710A Tuning Slider, 9V Base Battery: étape 3, image 1 de 2 Lubricate General Electric Telephone 2-9710A Tuning Slider, 9V Base Battery: étape 3, image 2 de 2

    • Remove the battery compartment door (located on the bottom of the radio) by applying thumb pressure to the area indicated on the battery door.

    • Slide the door off of the battery compartment.

    • Remove the battery from the phone.

    Traduire

  5. Lubricate General Electric Telephone 2-9710A Tuning Slider, Remove Volume Dial: étape 4, image 1 de 2 Lubricate General Electric Telephone 2-9710A Tuning Slider, Remove Volume Dial: étape 4, image 2 de 2

    • Ensure the phone is unplugged from the phone jack and the electrical source.

    • Locate the volume dial on the right side of the telephone.

    • Remove the volume dial by gently grasping it and pulling it away from the base.

    Traduire

  6. Lubricate General Electric Telephone 2-9710A Tuning Slider, Remove Screws on the Back: étape 5, image 1 de 1

    • Remove the three 12 mm screws with a Phillips #1 screwdriver.

    • Remove the three 18 mm screws with a Phillips #1 screwdriver.

    Traduire

  7. Lubricate General Electric Telephone 2-9710A Tuning Slider, Pry the Back Off: étape 6, image 1 de 2 Lubricate General Electric Telephone 2-9710A Tuning Slider, Pry the Back Off: étape 6, image 2 de 2

    • Pry off the base shell using a plastic opener tool.

    • Set the shell aside.

    • You now have access to the internal components of the General Electric Telephone 2-9710A.

    Traduire

  8. Lubricate General Electric Telephone 2-9710A Tuning Slider, Lubricate General Electric Telephone 2-9710A Tuning Slider: étape 7, image 1 de 2 Lubricate General Electric Telephone 2-9710A Tuning Slider, Lubricate General Electric Telephone 2-9710A Tuning Slider: étape 7, image 2 de 2

    • Turn the tuning slider counter clockwise all they way.

    • Apply lubricant to slider rail

    • Turn the tuning slider back and forth to distribute lubricant

    • CAUTION: Make sure lubricant does not circuit board. This can damage the circuit board.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 7 autres contributeurs

Alles Rebel

Membre depuis le 09/20/12

72 Réputation

3 tutoriels rédigés

Badges: 8

+ 5 badges supplémentaires

Équipe

Cal Poly, Team 16-59, Forte Fall 2012 Membre de l'équipe Cal Poly, Team 16-59, Forte Fall 2012

CPSU-FORTE-F12S16G59

4 membres

17 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 12

Total : 766