Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Boutique

Introduction

If you need to replace some pieces (like the brusholder circuit), this guide will help you disassembling the pump.

  1. Put the pump on the table, heading up. Unscrew the 4 screws with the screwdriver. Remove the O-ring.
    • Put the pump on the table, heading up.

    • Unscrew the 4 screws with the screwdriver.

    • Remove the O-ring.

  2. Using the flat head screwdriver apply some force between two teeth and try to lift the gear. Use the other hand or a plier (usually you don't need it) to take the first gear away. Remove the second gear. Remove the key, with the help of the flat head screwdriver: try to raise it from the bottom.
    • Using the flat head screwdriver apply some force between two teeth and try to lift the gear. Use the other hand or a plier (usually you don't need it) to take the first gear away.

    • Remove the second gear.

    • Remove the key, with the help of the flat head screwdriver: try to raise it from the bottom.

    • Don't forget to remove the key! If you do, you won't be able to continue.

  3. OUVRIR TOUS LES ONGLETS

    Kits de mise à jour de RAM pour Mac

    Voir les kits

    Assez de RAM
    pour ouvrir tous les onglets

    Voir les kits
  4. Unscrew the nuts on the back using the socket wrench screwdriver. Take away the washer and the little O-rings.
    • Unscrew the nuts on the back using the socket wrench screwdriver.

    • Take away the washer and the little O-rings.

  5. Keep your thumb on the shaft and lift the pump's head pulling from the hosefittings. Then, again, keep your thumb on the shaft and lift the motor's stator. Be careful: the magnetic field is strong, your finger may squeeze between the parts!
    • Keep your thumb on the shaft and lift the pump's head pulling from the hosefittings.

    • Then, again, keep your thumb on the shaft and lift the motor's stator.

    • Be careful: the magnetic field is strong, your finger may squeeze between the parts!

  6. If the rotor gets stuck in the stator, push it from the bottom and pull it from the other side. You need to have them separated, to assembly those back again. You can now pull out the bearing and the spring from the back plate, using the flat screwdriver or the rotor shaft.
    • If the rotor gets stuck in the stator, push it from the bottom and pull it from the other side.

    • You need to have them separated, to assembly those back again.

    • You can now pull out the bearing and the spring from the back plate, using the flat screwdriver or the rotor shaft.

  7. These are the pieces that you've just disassembled.
    • These are the pieces that you've just disassembled.

Conclusion

If you need to assemble the pump, use this guide: Marco UP Series Electric Pump Assembly

4 autre(s) ont terminé cette réparation.

Marco Spa

Membre depuis le 04/12/2015

1 189 Réputation

5 tutoriels rédigés

Domanda stupida: la pompa riceve corrente,gli ingranaggi (smontando la parte che li contiene) girano con una minima sollecitazione) il fusibile non salta…ma la pompa non parte! che faccio? …sono in grecia e volevo provare a sbloccarla prima di darmi battuto Grazie stefano

cippura - Réponse

Buongiorno,

se il motore parte (si muove) ma la pompa non muove acqua, sembrerebbe che le manchi la “chiavetta” che trasmette il moto dell’albero all’ingranaggio (passaggio 2 della guida). Nel caso non fosse questo il problema o volesse acquistare una nuova chiavetta, le suggerisco di scrivere a support@marco.it per una gestione diretta del problema con l’azienda e i loro tecnici.

teofranceschini -

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 1

7 derniers jours : 9

30 derniers jours : 44

Total : 2,286