Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. , Partie supérieure du boîtier: étape 1, image 1 de 2 , Partie supérieure du boîtier: étape 1, image 2 de 2
    • Éteignez votre Mac mini, déconnectez tous les câbles et retournez-le.

    • Insérez la spatule Jimmy dans la jointure entre l'aluminium du couvercle supérieur e de la partie inférieure en plastique.

    • La spatule doit s'enfoncer d'environ 9 mm.

    A spackle knife makes these steps go much faster.

    jouniseppanen - Réponse

    A double sided letter opener or a thin non-serrated butter knife will suffice.

    To prenent cosmetic blemishes, place a matchbook cover or similar thin cardboard on the outer perimeter under the “jimmy”.

    Mike - Réponse

  2. : étape 2, image 1 de 3 : étape 2, image 2 de 3 : étape 2, image 3 de 3
    • Penchez légèrement la spatule vers l'extérieur pour faire levier et élargir la fente et soulevez légèrement le boîtier inférieur.

    • Plusieurs clips en plastique sur le boîtier inférieur s’insèrent dans un canal du boîtier supérieur en aluminium. Votre objectif est de pousser ces clips suffisamment avec la spatule vers l’intérieur pour les dégager du canal, tout en tirant doucement le boîtier inférieur vers le haut.

    Patience is your best friend.

    Do not insert “jimmy in too far. Marking a line from tip upwards on the tool will prevent too far insertion, possibly breaking tabs or damaging internal components.

    To prevent the cover closing back up, small strips of matchbook cover (os equivalent) can be inserted about half inch hold prevent closure.

    Mike - Réponse

  3. : étape 3, image 1 de 2 : étape 3, image 2 de 2
    • Une fois que vous avez libéré le premier côté, faites pivoter le Mac mini et commencez à faire levier sur le bord avant.

    • Utilisez le même mouvement de levier pour replier les clips vers l’intérieur et soulever le boîtier inférieur afin de le sortir du boîtier supérieur.

  4. : étape 4, image 1 de 2 : étape 4, image 2 de 2
    • Vous devrez peut-être déplacer la spatule le long du bord pour ouvrir tous les clips. Soyez prudent et progressez petit à petit.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 5, image 1 de 2 : étape 5, image 2 de 2
    • Keep working around the perimeter, freeing the clips along the final edge.

  6. : étape 6, image 1 de 2 : étape 6, image 2 de 2
    • Retournez le Mac mini et soulevez le boîtier supérieur du boîtier inférieur.

    Before reassembly, make sure no wires are sticking out.

    Line up top cover carefully. Gently press down on top cover until top and bottom fully seated.

    CAUTION! DO NOT PRESS TOO HARD ON THE COVER TO PREVENT CRACKING THE PLASTIC TOP.

    GO EASY.

    Mike - Réponse

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 1
    • If your mini does not have Airport installed, then skip this step.

    • Grasp the Airport antenna board and lift it off of the two plastic posts holding it in place. You may need to push back the black plastic tab jutting through the lower left corner of the board.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 8, image 1 de 1
    • Remove the yellow tape securing the power button cable to the black plastic framework.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 9, image 1 de 1
    • Remove the three black Phillips screws securing the plastic framework to the logic board and lower case.

  10. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 10, image 1 de 1
    • Grasp the optical drive and mass storage unit in one hand and lift up enough so that you can see beneath it.

    I just put in a 1G RAM chip that just came in the mail from iFixit. And though I followed every step this step (removing the HD, cooling fan, and drive unit) was not needed. I put the chip in, put everything back in place then removed and replaced the RAM with no problems. So it would seem that for a/my PowerPC Mac Mini (I have a 1.33 Ghz processor) it was not a needed step.

    mbob518 - Réponse

    BTW, it took about 15 - 20 min even with my experimentation.

    Citation de mbob518 :

    I just put in a 1G RAM chip that just came in the mail from iFixit. And though I followed every step this step (removing the HD, cooling fan, and drive unit) was not needed. I put the chip in, put everything back in place then removed and replaced the RAM with no problems. So it would seem that for a/my PowerPC Mac Mini (I have a 1.33 Ghz processor) it was not a needed step.

    mbob518 - Réponse

  11. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 11, image 1 de 1
    • If your mini has neither an Airport card nor a Bluetooth board, you can simply lift the optical drive up and away. Otherwise, you need to disconnect the Airport and/or Bluetooth antenna cables first.

    • With your free hand, pull the Bluetooth cable up from Bluetooth board and unplug the Airport antenna cable from the right of the Airport card. Caution: both of these connections are very small. When re-assembling unit after repair, you may want to remove the two screws holding the airport card to the assembly and lift the card up and out to re-attach the cables.

    havin a hard time with step 9. i don't really see how I'm supposed to remove the Wi-Fi/Bluetooth cables from the Airport card. They seem to be soldered in! is there a twisting motion involved? I just don't wanna mess it up more than i already did with my putty knife haha!

    chris - Réponse

    Same problem here on this one. There seems to be no way to get them off and I can't seem to unscrew this thing. I think this otherwise great guide should be more precise about how to get the antenna cables out of the way :-(

    sebastian.patting - Réponse

    Antenna cables just pop off - straight up.

    Must be perfectly aligned when reconnecting as well before you re-seat them.

    Small needle nose pliers may be useful or a spudger or flat jewelers screwdriver to pry up on the cable as close to the connector as possible.

    rockpiano54 - Réponse

  12. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 12, image 1 de 1
    • Remove the four silver Phillips screws attaching the optical drive to the black plastic framework (two on each side).

  13. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 13, image 1 de 1
    • If your mini does not have a Bluetooth board, you may skip the following step.

    • Remove the yellow tape securing the Bluetooth antenna cable to the black plastic framework.

    • Lift the silver Bluetooth antenna board out of its slot.

  14. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 14, image 1 de 1
    • The cables you're about to remove are very fragile - do not pull directly on the wires. Instead, try to pry up the connector directly, using your fingernails or a small flathead screwdriver if necessary.

    • Flip the mass storage assembly over and disconnect the speaker and fan cables from the interface board.

  15. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 15, image 1 de 1
    • Flip the mass storage assembly back over. Grasp either side of the plastic framework and push the optical drive away from you with your thumbs on either side of the bezel until you hear it pop free.

    • Lift the optical drive and attached interface board up from the assembly.

  16. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 16, image 1 de 1
    • Remove the two silver Phillips screws connecting the interface board to the optical drive.

  17. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 17, image 1 de 1
    • Grasp either side of the interface board and wiggle it free of the optical drive.

Ligne d'arrivée

20 autres ont terminé cette réparation.

Pièces jointes

iRobot

Membre depuis le 09/24/09

1 Réputation

636 tutoriels rédigés

Un commentaire

If you are careful, there is no need to remove the whole storage unit and can unscrew the optical drive after removing the top case. The screws at the back are a bit tricky, but not impossible to remove while the storage unit remains attached to the logic board and bottom cover.

Miles Raymond - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 5

30 derniers jours : 26

Total : 22,639