Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Pièces & Outils

    • Arrêtez et fermez votre ordinateur. Posez-le sur une surface douce, la partie supérieure vers le bas.

    • Retirez les dix vis suivantes :

    • Deux vis pentalobes 8 mm 5-points

    • Huit vis pentalobes 2.5 mm 5-points

    • Le tournevis spécial nécessaire pour enlever les 5 points vis pentalobes peut être trouvé ici.

  1. Calez vos doigts entre l'écran et le boîtier inférieur et tirez vers le haut pour faire apparaître le boîtier inférieur de l'ordinateur.
    • Calez vos doigts entre l'écran et le boîtier inférieur et tirez vers le haut pour faire apparaître le boîtier inférieur de l'ordinateur.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    In this step you will disconnect the battery to help avoid shorting out any components during service. Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
    • In this step you will disconnect the battery to help avoid shorting out any components during service.

    • Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.

    • Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    Use the flat end of a spudger to pry the left and right I/O board cable connectors up off their respective sockets on the I/O board. Use the flat end of a spudger to pry the left and right I/O board cable connectors up off their respective sockets on the I/O board.
    • Use the flat end of a spudger to pry the left and right I/O board cable connectors up off their respective sockets on the I/O board.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    Lift and remove the I/O board cable.
    • Lift and remove the I/O board cable.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    Use the tip of a spudger to carefully push on each side of the iSight camera cable connector to loosen it out of its socket on the logic board. We recommend you gently "walk" the connector out of its socket.
    • Use the tip of a spudger to carefully push on each side of the iSight camera cable connector to loosen it out of its socket on the logic board.

    • We recommend you gently "walk" the connector out of its socket.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    Peel the iSight camera cable up off the adhesive securing it to the fan. Peel the iSight camera cable up off the adhesive securing it to the fan.
    • Peel the iSight camera cable up off the adhesive securing it to the fan.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket. Be sure you are prying up on the hinged retaining flap, not the socket itself.
    • Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    Remove the following three screws securing the fan to the upper case:
    • Remove the following three screws securing the fan to the upper case:

    • Two 5.5 mm T5 Torx screws

    • One 4.6 mm T5 Torx screw

    • In some models this is a 3.6 mm T5 Torx screw.

  9. Essential Electronics Toolkit

    Petit kit. Grandes possibilités.

    Shop Toolkits

    Essential
    Electronics
    Toolkit

    Shop Toolkits
  10. Cette étape n’est pas traduite. Aidez à la traduire

    Lift, but do not remove the fan out of its recess in the upper case. Carefully pull the fan ribbon cable out of its socket as you remove the fan from the Air. Carefully pull the fan ribbon cable out of its socket as you remove the fan from the Air.
    • Lift, but do not remove the fan out of its recess in the upper case.

    • Carefully pull the fan ribbon cable out of its socket as you remove the fan from the Air.

  11. Cette étape n’est pas traduite. Aidez à la traduire

    Use the flat end of a spudger to pry both antenna connectors up from their sockets on the AirPort/Bluetooth card, and move them out of the way. Use the flat end of a spudger to pry both antenna connectors up from their sockets on the AirPort/Bluetooth card, and move them out of the way. Use the flat end of a spudger to pry both antenna connectors up from their sockets on the AirPort/Bluetooth card, and move them out of the way.
    • Use the flat end of a spudger to pry both antenna connectors up from their sockets on the AirPort/Bluetooth card, and move them out of the way.

  12. Cette étape n’est pas traduite. Aidez à la traduire

    Remove the following five screws securing the battery to the upper case:
    • Remove the following five screws securing the battery to the upper case:

    • Two 5.2 mm T5 Torx screws

    • One 6 mm T5 Torx screw

    • Two 2.6 mm T5 Torx screws

  13. Cette étape n’est pas traduite. Aidez à la traduire

    When handling the battery, avoid squeezing or touching the six exposed lithium polymer cells.
    • When handling the battery, avoid squeezing or touching the six exposed lithium polymer cells.

    • Lift the battery from its edge nearest the logic board and remove it from the upper case.

  14. Cette étape n’est pas traduite. Aidez à la traduire

    Disconnect the I/O board by pulling the power cable away from its socket on the logic board. Pull the cable parallel to the face of the logic board toward the front edge of the Air.
    • Disconnect the I/O board by pulling the power cable away from its socket on the logic board.

    • Pull the cable parallel to the face of the logic board toward the front edge of the Air.

  15. Cette étape n’est pas traduite. Aidez à la traduire

    Use the tip of a spudger to de-route the antenna cables from their notches in the logic board. Use the tip of a spudger to de-route the antenna cables from their notches in the logic board. Use the tip of a spudger to de-route the antenna cables from their notches in the logic board.
    • Use the tip of a spudger to de-route the antenna cables from their notches in the logic board.

  16. Cette étape n’est pas traduite. Aidez à la traduire

    Gently push the tip of a spudger under the black plastic flap stuck to the display data cable lock to make the lock pop upward and away from the socket. While holding the lock away from the socket, gently pull the display data cable out of its socket. Do not pull upward on the display data cable as you disconnect it, as its socket may break off the logic board.
    • Gently push the tip of a spudger under the black plastic flap stuck to the display data cable lock to make the lock pop upward and away from the socket.

    • While holding the lock away from the socket, gently pull the display data cable out of its socket.

    • Do not pull upward on the display data cable as you disconnect it, as its socket may break off the logic board.

  17. Cette étape n’est pas traduite. Aidez à la traduire

    Use the tip of a spudger to pry under the speaker cable connector, lifting it straight up from its socket. De-route the  cable from its notch in the logic board. De-route the  cable from its notch in the logic board.
    • Use the tip of a spudger to pry under the speaker cable connector, lifting it straight up from its socket.

    • De-route the cable from its notch in the logic board.

  18. Cette étape n’est pas traduite. Aidez à la traduire

    Use the tip of a spudger or your fingernail to flip up the retaining flap on the trackpad ribbon cable ZIF socket. Be sure you are prying up on the hinged retaining flap, not the socket itself. Pull the trackpad ribbon cable straight out of its socket toward the front edge of the Air.
    • Use the tip of a spudger or your fingernail to flip up the retaining flap on the trackpad ribbon cable ZIF socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

    • Pull the trackpad ribbon cable straight out of its socket toward the front edge of the Air.

  19. Cette étape n’est pas traduite. Aidez à la traduire

    Use the tip of a spudger to flip up the retaining flap on the keyboard backlight ribbon cable ZIF socket. Be sure you are prying up on the hinged retaining flap, not the socket itself. Pull the keyboard backlight ribbon cable out of its socket.
    • Use the tip of a spudger to flip up the retaining flap on the keyboard backlight ribbon cable ZIF socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

    • Pull the keyboard backlight ribbon cable out of its socket.

  20. Cette étape n’est pas traduite. Aidez à la traduire

    Remove the single 2.9 mm T5 Torx screw securing the AirPort/Bluetooth card to the logic board.
    • Remove the single 2.9 mm T5 Torx screw securing the AirPort/Bluetooth card to the logic board.

  21. Cette étape n’est pas traduite. Aidez à la traduire

    Slightly lift the free end of the AirPort/Bluetooth board and pull it out of its socket on the logic board. To avoid damaging its socket on the logic board, do not excessively lift the free end of the AirPort/Bluetooth card. To avoid damaging its socket on the logic board, do not excessively lift the free end of the AirPort/Bluetooth card.
    • Slightly lift the free end of the AirPort/Bluetooth board and pull it out of its socket on the logic board.

    • To avoid damaging its socket on the logic board, do not excessively lift the free end of the AirPort/Bluetooth card.

  22. Cette étape n’est pas traduite. Aidez à la traduire

    Remove the three 3.6 mm T5 Torx screws securing the logic board to the upper case.
    • Remove the three 3.6 mm T5 Torx screws securing the logic board to the upper case.

    • In some models these are 3.1 mm T5 Torx screws.

  23. Cette étape n’est pas traduite. Aidez à la traduire

    Gently lift the logic board assembly from the heat sink end and pull it away from the port side of the case to remove it from the Air. When replacing the logic board, insert the board's rubber edge under the port-side rubber gasket, then lower the board into place. When replacing the logic board, insert the board's rubber edge under the port-side rubber gasket, then lower the board into place.
    • Gently lift the logic board assembly from the heat sink end and pull it away from the port side of the case to remove it from the Air.

    • When replacing the logic board, insert the board's rubber edge under the port-side rubber gasket, then lower the board into place.

  24. Cette étape n’est pas traduite. Aidez à la traduire

    Remove the four 2.5 mm T5 Torx screws securing the heat sink to the logic board.
    • Remove the four 2.5 mm T5 Torx screws securing the heat sink to the logic board.

  25. Cette étape n’est pas traduite. Aidez à la traduire

    • If the heat sink seems to be stuck to the logic board after removing all four screws, use a spudger to carefully separate the heat sink from the faces of the CPU.

    • Remove the heat sink from the logic board.

    • When reinstalling the heat sink, be sure to apply a new layer of thermal paste. If you have never applied thermal paste before, we have a guide that makes it easy.

  26. Cette étape n’est pas traduite. Aidez à la traduire

    Remove the single 2.9 mm T5 Torx screw securing the SSD to the logic board.
    • Remove the single 2.9 mm T5 Torx screw securing the SSD to the logic board.

  27. Cette étape n’est pas traduite. Aidez à la traduire

    Lift the free end of the SSD just enough to get a good hold of it. Do not excessively lift the end of the SSD. Pull the drive straight out of its socket and remove it from the logic board.
    • Lift the free end of the SSD just enough to get a good hold of it.

    • Do not excessively lift the end of the SSD.

    • Pull the drive straight out of its socket and remove it from the logic board.

    • When reinstalling the SSD, be sure it is properly seated before reinstalling its retaining screw.

Ligne d'arrivée

12 autre(s) ont terminé cette réparation.

Sam Goldheart

Membre depuis le 18/10/2012

406 919 Réputation

547 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

114 membres

11 085 tutoriels rédigés

Thank you so much! This actually wasn't difficult at all, especially following your guide! I was able to fix my dad's computer with a replacement logic board. He's going to be super happy about this!

Robin H - Réponse

I don’t see a difference between this and the guide for the Early 2014 11” MacBook Air. Is there a difference or can I replace my dead 2014 Air’s Logic Board with a 2015? That Thunderbolt 2 port would be really helpful!

vnangia - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 6

7 derniers jours : 29

30 derniers jours : 182

Total : 9,978