Introduction

Use this guide to replace a burned-out fan.

Vidéo d'introduction

    • Before proceeding, close your computer and lay it on a soft surface top-side down.

    • Remove the following ten screws:

      • Two 9 mm 5-point Pentalobe screws

      • Eight 2.6 mm 5-point Pentalobe screws

    • The special screwdriver needed to remove the eight 5-point Pentalobe screws can be found here.

    Ajouter un commentaire

  1. Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
    • Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

    • Remove the lower case and set it aside.

    Ajouter un commentaire

    • For precautionary purposes, we advise that you disconnect the battery connector from the logic board to avoid any electrical discharge. This step is optional and is not required.

    • Grab the clear plastic pull tab attached to the battery connector and pull it toward the front edge of the Air to disconnect the battery from the logic board.

    • Do not lift upward on the connector as you disconnect it.

    Ajouter un commentaire

    • Use the flat end of a spudger to pry the I/O board cable connector upward out of its socket on the I/O board.

    Die nachfolgenden Schritte sind nicht erforderlich. Bitte bei Schritt 11 weitermachen.

    Volker - Réponse

    Es ist nicht erforderlich, IO-Board, Akku und Logic-Board auszubauen. Es genügt, die Antennen- das Kamera- und das Displaykabel zu entfernen und die Scharniere abzumontieren. Die Kabel können leicht an den vorhandenen Komponenten vorbeigezogen werden.

    Volker - Réponse

    • The following connector has an especially deep socket. Use care when disconnecting it.

    • Carefully peel the I/O board cable from the top of the fan.

    • While gently pulling the I/O board cable upward near its connection to the logic board, use the tip of a spudger to pry upward on alternating sides of the connector to help "walk" it out of its socket.

    • Remove the I/O board cable.

    Ajouter un commentaire

    • Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

    Ajouter un commentaire

    • Peel the rubber gasket off the adhesive on the top of the fan.

    Ajouter un commentaire

    • Remove the following three screws securing the fan to the upper case:

      • One 3.6 mm T5 Torx screw

      • One 2.7 mm T5 Torx screw

      • One 3.6 mm T5 Torx screw with a short head

    Ajouter un commentaire

    • Lift the fan out of the upper case and carefully pull the fan ribbon cable out of its socket as you remove it from the Air.

    Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

16 autre(s) ont terminé cette réparation.

Plugging the fan back in is a huge pain in the ass, do you have a tip for that?

Robert Westman - Réponse

I screwed up and my fan cable ZIF socket lifted out. I destroyed it trying to solder it back on. Can I buy a replacement?

Janine Maddock - Réponse

This is actually an interesting question. I was looking into this issue and watched most of your video and the fan did not spin up and everything was quiet and perfect. If I watch a youtube video, it spins up like crazy. Any suggestions?

Jerry Garcia - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 6

7 derniers jours : 24

30 derniers jours : 103

Total : 18,339