Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Utilisez un tournevis P5 Pentalobe pour retirer les dix vis qui fixent le boîtier inférieur, dont les dimensions sont les suivantes :
-
Deux vis de 9 mm
-
Huit vis de 2,6 mm
-
-
-
Saisissez la petite languette en plastique transparent attachée au connecteur de la batterie, et tirez-la vers l'avant du MacBook Air pour déconnecter la batterie de la carte mère.
-
-
-
-
Soulevez la batterie par le bord le plus près de la carte mère et retirez-la du boîtier supérieur.
-
Chargez l'ordi à 100 %, puis laissez-le se charger pendant au moins 2h supplémentaires. Puis, débranchez-le et utilisez-le normalement pour vider la batterie.
-
Quand l'alerte de batterie faible s'affiche, sauvegardez votre travail et laissez votre ordi allumé jusqu'à ce qu'il force la mise en veille. Attendez au moins 5h, puis chargez votre portable sans interruption jusqu'à 100 %.
-
Si vous constatez un comportement inhabituel ou des problèmes après l'installation de votre nouvelle batterie, vous pourrez avoir besoin de réinitialiser le SMC de votre MacBook.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the tip of a spudger or your fingernail to flip up the retaining flap on the trackpad ribbon cable ZIF socket.
-
Pull the trackpad ribbon cable straight out of its socket toward the rear edge of the Air.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
While carefully lifting the keyboard ribbon cable with one hand, use the tip of a spudger or your fingernail to flip up the retaining flap on the keyboard ribbon cable ZIF socket.
-
Pull the keyboard ribbon cable straight out of its socket toward the front edge of the Air.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following twelve screws:
-
Six 1.6 mm Phillips screws securing the trackpad to the upper case.
-
Six 1.6 mm Phillips screws securing the trackpad brackets to the trackpad.
-
A Phillips #000 should be sufficient, but a JIS #000 may also work as well.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the right and left trackpad brackets from the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the 1.4 mm T5 Torx set screw from its tapped hole near the front edge of the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat edge of a spudger to carefully lift the edge of the trackpad closest to the keyboard from its recess in the upper case by lifting it away from the brackets attached to the upper case.
-
Remove the trackpad from the upper case.
-
Annulation : je n'ai pas terminé ce tutoriel.
44 autres ont terminé cette réparation.
6 commentaires
Hey guys,
just repaired my "old" 2012 Air's touchpad and thanks to your great instruction it took me exactly 30 Mins and was super easy...
Thanks for your great work!
@peter: yes, it needs a bit fiddling with the cables - just keep an eye on the flaps (they are closed on the new TP). Then it helped me to press the cable slightly in place with one hand and carefully pushing it in (moving it slightly left and right) with the other.
Great guide!! recently repaired two mb air of my office, great parts!!! great guide
step 10 is not needed, in my second repair of this model I didn't remove it, this screw is only for calibration
Right. Step 10 is not only not needed but should definitely not be done! This is a pure adjustment screw for the clickpoint. Only readjust there, in case clicking does not feel okay after a change of the trackpad. Usually no adjusment is necessary.