Réparez vos affaires

Droit à la réparation

Boutique

MacBook Air Models A1237 and A1304 AirPort/Bluetooth Board Replacement

Rédigé par : Walter Galan (et 4 autres contributeurs)
  • Commentaires : 0
  • Favoris : 11
  • Réparations terminées : 9

Difficulté

Modérée

Étapes

9

Sections

3

Drapeaux

0

Introduction

Reclaim your singular source of internet connectivity by replacing your broken AirPort/Bluetooth board.

  1. Unplug your MacBook Air and power it off before you proceed.

    • Unplug your MacBook Air and power it off before you proceed.

    • Remove ten Phillips screws securing the lower case to the MacBook Air:

    • Six 2.8 mm screws

    • Two 3.8 mm screws

    • Two 5.4 mm screws

    Traduire

  2. Slightly lift the lower case near the vents and push it toward the rear of the computer to free the mounting tabs. Slightly lift the lower case near the vents and push it toward the rear of the computer to free the mounting tabs.

    • Slightly lift the lower case near the vents and push it toward the rear of the computer to free the mounting tabs.

    Traduire

  3. Disconnect the battery connector by pulling it straight out of its socket.

    • Disconnect the battery connector by pulling it straight out of its socket.

    Traduire

  5. Remove the following nine screws securing the battery to the Air:

    • Remove the following nine screws securing the battery to the Air:

    • Four 2.9 mm Phillips.

    • Four 3.8 mm Phillips.

    • One 7.2 mm Phillips.

    Traduire

  6. Lift the battery out of the Air.

    • Lift the battery out of the Air.

    • If you're installing a new battery, you should calibrate it after installation:

    • Charge it to 100%, and then keep charging it for at least 2 more hours. Then, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.

    • If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook's SMC.

    Traduire

  7. Remove the two following screws securing the AirPort/Bluetooth board bracket to the upper case: One 4.7 mm Phillips.

    • Remove the two following screws securing the AirPort/Bluetooth board bracket to the upper case:

    • One 4.7 mm Phillips.

    • One 3.9 mm Phillips.

    • Lift the AirPort/Bluetooth bracket out of the upper case.

    Traduire

  8. Using a spudger, pry the AirPort/Bluetooth ribbon cable connector straight up off the AirPort/Bluetooth board.

    • Using a spudger, pry the AirPort/Bluetooth ribbon cable connector straight up off the AirPort/Bluetooth board.

    Traduire

  9. Use a spudger to pry the three antenna cables up off the AirPort/Bluetooth board.

    • Use a spudger to pry the three antenna cables up off the AirPort/Bluetooth board.

    Traduire

  10. Remove the single 3.2 mm Phillips screw from the upper right corner of the AirPort/Bluetooth board. Lift the AirPort/Bluetooth board out of the upper case.

    • Remove the single 3.2 mm Phillips screw from the upper right corner of the AirPort/Bluetooth board.

    • Lift the AirPort/Bluetooth board out of the upper case.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

9 autre(s) ont terminé cette réparation.

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 1

7 derniers jours : 13

30 derniers jours : 49

Total : 36,316