Menu 

Vos paramètres

Mon établi

Accédez rapidement aux tutoriels, aux pièces et aux réponses correspondant à vos appareils
Mon panier (US Store)

On dirait que votre panier est vide

Parcourez notre boutique

MacBook Air Models A1237 and A1304 Speaker Replacement

Rédigé par : Walter Galan (et 3 autres contributeurs)
  • Commentaires : 0
  • Favoris : 7
  • Réparations terminées : 4

Difficulté

Modérée

Étapes

12

Sections

4

Drapeaux

0

Introduction

Restore sound to your laptop by replacing the speaker.

Outils

Acheter ces outils

Pièces

Acheter ces pièces

  1. Unplug your MacBook Air and power it off before you proceed.

    • Unplug your MacBook Air and power it off before you proceed.

    • Remove ten Phillips screws securing the lower case to the MacBook Air:

      • Six 2.8 mm screws

      • Two 3.8 mm screws

      • Two 5.4 mm screws

    Traduire

  2. Slightly lift the lower case near the vents and push it toward the rear of the computer to free the mounting tabs. Slightly lift the lower case near the vents and push it toward the rear of the computer to free the mounting tabs.

    • Slightly lift the lower case near the vents and push it toward the rear of the computer to free the mounting tabs.

    Traduire

  3. Disconnect the battery connector by pulling it straight out of its socket.

    • Disconnect the battery connector by pulling it straight out of its socket.

    Traduire

  4. Remove the following nine screws securing the battery to the Air:

    • Remove the following nine screws securing the battery to the Air:

      • Four 2.9 mm Phillips.

      • Four 3.8 mm Phillips.

      • One 7.2 mm Phillips.

    Traduire

  5. %Livraison gratuite pour toute commande supérieure à 100,00 $US ou contenant un Pro Tech Toolkit !

    Parcourez notre boutique

    Vous avez déjà réparé quelque chose ? Vous êtes un génie.

    Partagez votre réparation avec le hashtag #ImAGenius

    Nous sommes tous des génies

    Partagez votre réparation avec le hashtag #ImAGenius

  6. Lift the battery out of the Air.

    • Lift the battery out of the Air.

    • If you're installing a new battery, you should calibrate it after installation:

      • Charge it to 100%, and then keep charging it for at least 2 more hours. Then, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.

      • If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook's SMC.

    Traduire

  7. Remove the following two screws securing the speaker assembly to the upper case.

    • Remove the following two screws securing the speaker assembly to the upper case.

      • One 3 mm Phillips.

      • One 5.8 mm Phillips.

    Traduire

  8. Use a spudger to lift the audio-out connector board off the adhesive that secures it to the hard drive bracket. Disconnect the audio out connector from its socket.

    • Use a spudger to lift the audio-out connector board off the adhesive that secures it to the hard drive bracket.

    • Disconnect the audio out connector from its socket.

    Traduire

  9. Rotate the speaker assembly toward the center of the Air. Use a spudger to pry the speaker cable connector up off the audio board.

    • Rotate the speaker assembly toward the center of the Air.

    • Use a spudger to pry the speaker cable connector up off the audio board.

    Traduire

  10. Use the tip of a spudger to pry the speaker connector up off the audio board.

    • Use the tip of a spudger to pry the speaker connector up off the audio board.

    Traduire

  11. Use the tip of a spudger to separate the audio board from the adhesive securing it to the logic board.

    • Use the tip of a spudger to separate the audio board from the adhesive securing it to the logic board.

    Traduire

  12. Disconnect the audio-out cable by pulling the male end straight away from its socket on the audio board.

    • Disconnect the audio-out cable by pulling the male end straight away from its socket on the audio board.

    Traduire

  13. Speaker assembly remains.

    • Speaker assembly remains.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

4 autre(s) ont terminé cette réparation.

0 commentaires

Ajouter un commentaire
Voir les statistiques:

Dernières 24 heures : 2

7 derniers jours : 16

30 derniers jours : 87

Total : 20,022