Introduction

Avec l'aide de ce tutoriel, remplacez un pavé tactile cassé.

Retirez les dix vis suivantes :
  • Retirez les dix vis suivantes :

    • Trois vis Phillips #00 14,4 mm

    • Trois vis Phillips #00 3,5 mm

    • Quatre vis à épaulement Phillips #00 3,5 mm

Does void the warranty?

jfondeur - Réponse

No, it does not void the warranty. More specifically: http://eshop.macsales.com/Search/display...

oakdragon12 - Réponse

How much weight can I save by removing the optical drive?

gunes314 - Réponse

You can save a lot of weight if lets say your installing a solid state drive or putting in a second hard drive but if you know that you use the CD/DVD disc drive a lot then you might just want to leave the drive alone.

Marshall WahlstromHelgren -

Also wondering how much weight I'd save by just removing. My drive is broken for ages, but I have not needed it in ages. The HD was already replaced by a cheap SSD (second best thing after upgrading to 8GB), so I'd appreciate losing some weight. I mean, the computer. Although I could lose some too... erm... well, anyway, I guess the lack of the DVD would not interfere with anything, right? Opinions?

Carlos Duarte do Nascimento - Réponse

Apple has meticulously balanced the MacBook's weight from left to right, and removing the optical drive may off-balance the Mac.

Seji the veggie -

What so you think that a removing the optical drive which weighs less than a AA battery will unbalance a MBP making it unusable? LOL!

Unless you use the MBP on a high wire (an even then I have my doubts) you'd never notice the weight difference.

pmhparis -

The issue is not one of weight but an issue with the systems cooling and an opening which objects could enter. For a few grams of weight I don’t think its worth it! A better solution would be to swap out the heaver HD for a much lighter SSD, and getting all of the performance benefits of the faster drive as well!

While you might not think it the optical drive also acts as a stiffener so there is less twist in the case. This is because of the size of the hole for the DVD/CD’s so taking it out weakens the case design.

Dan -

I'm thinking you'd probably be OK losing the DVD drive without a problem. Just make sure the optical drive cable is secured or you might hear it rattling in there from time-to-time.

John Adam Wickliffe - Réponse

Hey guys,

this website is amazing. I read it to guide me on fixing my mac book pro, but on the video, the girl gives a wrong information.. She says that is not possible replace just the keyboard... But I managed to replace only my keyboard. It is boring because I have to remove approximately 70 screws but it is possible. Thanks a lot! You guys helped me save about US$300 thats because in Brazil some technicians would charge me with that amount!

I posted some pictures on your facebook page..

renatumb - Réponse

Tip: Use one of those weekday pill holders to have a cheep way to store screws you remove and each day of the week can be for different sizes or parts. It has been handy to have (much less expensive than the magnetic mat.

Robert Wacker - Réponse

Great tutorial. I found that using a Phillips #0 in lieu of the #00 worked much better.

kschmesk - Réponse

I tried the PH #00 for the 10 screws that hold the bottom case and it's too big, instead PH #000 works perfectly. Are you sure this screws are #00?

Alex - Réponse

The likely problem with your wifi is not the card but the antenna leads that go into the plastic clutch

. Ifixit don't have a guide to change this as it it includes the isight camera so the screen has to be disassembled which is fairly hard

I got round it by using the camera cable from the old set and cutting off the new one

brian whittle - Réponse

Hello MacWorld,

Just want to say that this site is a great resource for repairing or upgrading your Mac. I had a bad SATA cable in my MacBook Pro and after ordering a new one from the "IFIXIT" site I received the cable within two days, replaced it and was up and running again in no time. Thanks IFIXIT for you help!

wer 10/5/15

tayseer999 - Réponse

I have found that my MacBook Pro 13 Late 2011 has five shouldered screws and not four. I am not sure exactly where it goes but I have put it in the top left corner of the picture as it is the odd one out.

GotMac - Réponse

Hello, where can I buy the screws I need in case I lose one of them?

taylornya - Réponse

on my device the #00 screwdriver was a bit too small. a #0 was the perfect one

Maximilian Klotz - Réponse

I found with mine that the shouldered and un-shouldered screws were reversed (the three un-shouldered screws going where the orange colour indicates). Also, I found that the front four screws went in at an angle.

gilded yak - Réponse

Are you sure the short screws are different? The set sold here just says “Seven 3 mm Phillips #00 screws.”

Jack - Réponse

I have the same question. What is the difference between shouldered and not? So hard to see any difference…

Michael Wilkens -

I have one stripped screw... How opening without drill it?! Any suggestions please?

rodrigosady - Réponse

I also stripped a couple screws. I wasn’t able to open it up without drilling. After drilling the heads and removing the cover it was easy to hacksaw the tip and unscrew with a standard driver.

Michael Wilkens -

I used 3 eggcups to hold the screws ;>) They are very fiddly and easy to drop on floor so keep the MacBook away from the edge of the surface you are using to avoid accidentally dropping a screw off the edge of a table, etc.

Stephen Smith - Réponse

A screw does not come out, how can I get it out? Many thanks in advance for your help

Wilder Torres - Réponse

Since you’ll be removing many screws it’s best to plan ahead. I found it especially helpful to have a small plastic tray with about a dozen separate compartments to hold screws. As I removed screws I kept them in one compartment for each item removed. For example: The lower case removal involves the removal of ten screws. I kept them all in the first tray compartment and set the lid aside. Also, I put a post-it note identifying this compartment as “Lower case” and noted that the top right-most screws were the long ones. I continued with this methodology as a removed the next item, and the next, etc. Disassembly notes included for each compartment. This helped SIGNIFICANTLY as I was able to reassemble the Macbook easily by simply going from one compartment to the next (in reverse order). This guide is rated “Difficult” which it really isn’t when you plan ahead in this way. It saves time in the long run.

airshack - Réponse

when putting the macbook pro back together, the middle screw on the right side (if the computer is upside down and you have the hinge furthest away from you) requires a bracket that was not included with my new upper case. i had to remove it from my old case and transfer it over - if you don’t do this, that screw will have nothing to attach to.

this was one of the many additional parts i needed to transfer from my old case to the new one that aren’t mentioned in this guide…i’m adding comments on each step to try to help others…i wish i had thought to take pictures.

Matt - Réponse

It seems to me the yellow and orange screws are the same

Luca Giancarli - Réponse

The screws used on all Retina models, as well as about everything Apple has made since the iPhone 4, uses “PENTALOBULAR” not Phillips screws. These look like a TORX driver, but it has 5 concave sides. I believe the size you want is a P4 or T4. (1.2mm).

Don Cely - Réponse

Two screw types:

______________________________

Shouldered Unshouldered

xxxxxxx……….xxxxxxx

..xxxxx……..….…….x…….

…..x……..…...……….x…….

…..x…………....……..x…….

______________________________

El Crashitan - Réponse

If you are following this guide to upgrade to a better drive and want to keep your system and data intact I highly recommend first following the guide to Clone an Existing Drive using the recommended free SuperDuper!. That process was a breeze and gives you confidence that the new drive will come up looking exactly the way it did when you started.

Patrick Langvardt - Réponse

Faites levier avec vos doigts au niveau de la fente pour sortir le boîtier inférieur de la coque du MacBook.
  • Faites levier avec vos doigts au niveau de la fente pour sortir le boîtier inférieur de la coque du MacBook.

  • Retirez le boîtier inférieur.

If the black vent window that is attached to the back cover becomes loose what kind of glue should be used to attach it again, thermal paste or super glue?

Thanks for your help.

Mikell - Réponse

bonjour cette truc ça marche au mac Brook pro Retina ou pas?

Shi Feng - Réponse

Bonjour, alors cela va dépendre du modèle de MacBook Pro Retina concerné. Par exemple, si vous avez un 13 pouces, allez consulter cette page MacBook Pro 13" Retina Display Repair et sélectionnez-y votre modèle. Les Retina 15 pouces se trouvent ici MacBook Pro 15" Retina Display Repair. Sinon cet outil https://fr.ifixit.com/info/ID-your-Mac (pour l’instant seulement disponible en anglais) vous aide à identifier quel modèle vous avez et vous redirige vers la page de votre appareil, où vous trouverez le tutoriel correspondant à votre Retina. Bonne réparation !

Claire Rapp -

Merhaba, trackpad değişimi ve ayarlaması için tornavidaya ihtiyacım var, bu konuda yardımcı olabilir misiniz acaba? Ne tür bir tornavidaya ihtiyacım var ve nereden bulabilirim acaba?

Volkan Ogul - Réponse

  • À l'aide de l'extrémité d'une spatule (spudger), faites levier sur le connecteur de la batterie pour le débrancher de la prise sur la carte mère.

  • Il convient d'appliquer l'effet de levier sur les deux côtés courts du connecteur. Faites attention aux coins des connecteurs, car ils se cassent facilement.

Is this step of removing the battery connector required?

manodh - Réponse

yes - as with disassembly of any electronic component you have to remove any power source. You don't want to accidentally turn the Mac on

khull -

Sooo the track pad is under the battery...you kind of have to remove it to get to the track pad.

stiknrudder -

This step is not really required. Apple does not recommend it.

Steven Layton - Réponse

My Battery does not get recognized after i disconnected it, screw this site!

Diego Hernandes -

Did you properly ground yourself to the case before putting the spudger to the connector/logic board? Did you use a spudger or something else that is non conductive...or did you use a flat blade metal screw driver instead and compound your error by not grounding yourself before touching the logic board? All kinds of variables here but the bottom line is iFixit provided you a guide to fix your computer. Lots of others have followed this guide without trouble. Your battery issues are not their fault. They did say this guide was moderate difficulty...maybe it's just a little beyond your skill level. We should all know our limits!

stiknrudder -

Rather than be careful of the corners of the connector i would say don't use the spudger anywhere near the corners. While the corner looks like the obvious place to begin to pry it up from, it will break. Levering from the sides as the instructions suggest works well.

ausmkv - Réponse

wonder why apple does not recommend it?!

Peter - Réponse

I would recommend it, one careless short and the whole board is dead......

John - Réponse

simply remove the battery rather than disconnecting the cable

toiu - Réponse

What do you mean by "remove the battery"?

Anrothan -

Don't know what the deal is with the battery, but this IS a necessary step to keep from frying the logic Board if you accidentally touch something and short it out. I did this step every time during my troubleshooting and The battery was ALWAYS recognized by the system the next time I turned the MBP on. So be safe and don't fry your logic board in the process...

fasthans - Réponse

Prying the battery connector off does not take much force. I did exactly what the guide suggested (walked it off back and forth) with the spudger without any problems. Just be very gentle, much like with anything inside laptops, they are very fragile and need to be worked with carefully. A+ instructions, battery replacement was a success.

aekinaka - Réponse

Installed/upgraded 4gb RAM to the system maximum 16gb and installed a 500 gb SSD today....DID NOT disconnect the battery cable....no issues at all when I powered back up. Then did a clean install of OSX Yosemite....next I used a time machine backup to put all my stuff back on the new HD. From start to finish it took about 4 hours. Macbook boots up right at 16 seconds now.

MacProUser - Réponse

Easiest to use two spudgers, one on each short end, I found.

Simon Mundy - Réponse

I took off th Airport /Bluetooth connectors but the number J3 connector is broken and so where can i buy J3 connecter for the Airport/bluetooth board

Zeerachen - Réponse

Its a lot easier and safer (corner wise) to pry it using the flat side of the black spudger directly in front of the connector (don't go/use the corners) very easily you will be able to pry it further by inserting the spudger into a better and thicker plastic section of the connector

Ed Oliver - Réponse

DON'T remove the Battery Cable, you risk the battery NOT being recognised when you start the Mac up again, or breaking it!! More to the point, APPLE DOES NOT RECOMMEND THIS, so don't do it! I Installed 2x 8GB ( 16Gb total) of Crucial Mac RAM at 1333Mhz for my Late 2011 MacBook Pro, and it works beautifully, fully recognised and working well. I followed these instructions, but as Apple didnt recommend disconnecting the battery, I skipped this step, and as well as taking less time, nothing was damaged or broken, and everything works perfectly!!! Just make sure that you DISCHARGE ALL STATIC ELECTRICITY FROM YOUR HANDS, by touching a metal surface in the Mac. Apple recommends the edge of the Optical Disk Drive ( Big silver thing ) before touching any parts. Also, Take care removing the RAM out of its packet, DO NOT touch the Gold connectors, and hold the RAM by the edges. Finally, be PATIENT, GENTLE and it should all go perfectly. I managed it first time, with no technical ability, so follow my advice. Good luck!

Bradley Marks - Réponse

Followed the tuto Step by step. Disconnected the battery (quite easily).

No problem when I lit the Mac on again. Battery's here, date's right.

nichoferr - Réponse

Switch off your Mac and continue without disconnecting the battery. Don't know how it will switch on by itself.

Mfernandez - Réponse

This comment made me think that disconnecting the battery was no point at all, because really - how would the computer be able to switch on by it self. So... I had my mac flipped around and was fiddling with the last part of the guide when I all of a sudden hear the start up sound! Don't know how and why it did. I turned it around with it guts open and guts hanging out. Screen was on. I forced it to shut down by keeping the power button down. Turned it back and first thing removed the battery cord.

Luckily the computer started up just like normal. But hearing that sound was just too scary.

BTW I had been cautious to de static myself multiple times.

wassberg -

Definitely do this step. It's an easy disconnect anyway and also easy to reconnect later.

Stephen Smith - Réponse

I removed the battery cable for the repair. When I plugged in the MagSafe adapter after the repair, the Mac turned on automatically without pressing the power button and I was a bit worried, but after a restart everything worked fine again. I did have to reset date and time in Preferences. The battery was recognized OK.

Raymond Rinaldi - Réponse

Okey, I skipped this battery disconnection part. Did not do anything like this before in my life, changing the cable was super easy!

Marijke de Vries - Réponse

The official Apple guide to replacing the RAM says nothing about disconnecting the battery but it does recommend touching metal inside to discharge static. https://support.apple.com/en-us/HT201165

B T - Réponse

I always do this when working on MacBooks (over ten years) and it never caused an issue. Don’t worry about this step as removal of the battery connector is simple. This particular connector is pretty much goof-proof as it won’t break. I’m fairly aggressive and just pop it off whenever I’m working on the Macbook Pro.

airshack - Réponse

Hello!

Do I really need to use a spudger tool? Can’t I just use like two plectrums for guitar? xD

Myzcio - Réponse

  • Repliez légèrement le câble de la batterie vers l'arrière pour éviter qu'il ne se reconnecte accidentellement à la prise sur la carte mère pendant que vous travaillez.

What are the changes of it broke when i bend it?, after i disconect it does not work anymore

Diego Hernandes - Réponse

The guide worked perfectly, as it has in the past (our family has three Mid-2012 Macbook Pros that have been separately upgraded with RAM and SSD).

The PH00 screwdriver fit perfectly.

One note on getting the screws to seat easily and thread perfectly...always turn them gently a couple turns to the left (CCW or Anti-Clockwise) until you hear a small click. That's where the threads will grab. Works with any screw, but when threads are fine, this will help ensure that the screw is at the correct angle and will grab and seat perfectly.

Great guides. Thanks!

timgunkel - Réponse

Got RAM in but only one slot is working and now I can't remove! The RAM won't pop up like before and tabs don't seem to do anything. Please advise.

Sal Ergrapes - Réponse

I put some tape between the connector and socket while working on the drive.

Stephen Smith - Réponse

That's a good tip

Anrothan -

Followed the advice and right as I was installing the replacement fan , the socket broke right off the motherboard.

Ian Thal - Réponse

One other note: The screw heads fit flush with the curvature of the case -- which means that they aren't exactly horizontal. In other words, they aren't perpendicular to the table that the computer is resting on. Don't try to force them straight in vertically, because you'll risk cross-threading them. (nearly ruined one screw hole myself!)

lelandjordon - Réponse

does the battery connection need to be removed? I only ask as other videos etc have not shown this step.

Darren Rose - Réponse

  • Retirez les deux vis suivantes :

    • Une vis Tri-point de 5,6 mm

    • Une vis Tri-point de 13 mm

Tri-wings are quite sensitive to which size driver to use. I found Pro'sKit brand size 0 seems to fit these very well.

James - Réponse

can i just take out my dead battery without replacing it,

and solely run my mbp on power supply to save weight and money?

Tosh - Réponse

I assume that REPLACING a new battery is the same steps but in reverse? Nothing special we need to look out for?

Also, please add some comments about watching out for STATIC ELECTRICITY. Other videos and websites make it seem frighteningly dangerous and recommend other tools to prevent static electricity discharge. If you could address this issue, I would greatly appreciate it.

erictwo - Réponse

Are the screws tri-wing or tri-point? There is a difference, but ifixit uses the terms as if they're interchangable. en.wikipedia.org/wiki/List_of_screw_drives#Tri-point

rodmanc - Réponse

These screws do absolutely NOT have the TRI-WING® recess. I find, the LHSTIX 3ULR MicroStix size 3ULR-0 driver fits perfectly.

unsubstantiated - Réponse

My battery (original to my late 2011 MBP) straight up does not have screws.

nlgauvreau - Réponse

  • Décollez délicatement l'autocollant d'avertissement du boîtier supérieur entre la batterie et le lecteur optique.

  • Ne retirez pas l'autocollant de la batterie.

What is the reasoning behind not removing the label from the (old) battery?

tom - Réponse

Probably to help you remove it? Not sure, but I used it along with the clear tab to pull the battery out. Worked pretty good.

aitorrecalde -

  • A l'aide de la languette en plastique attachée, retirez la batterie du boîtier supérieur.

Hey there !

i replaced my old battery with the one I purchased from ifixit following the guidance. Niw I have the problem, that my macbookpro 13” late 2011 doesn’t boot anymore and the led of my plug just blinks orange rapidly. What happened. Can anybody think of smth, or have had similar experiences?

Mak - Réponse

My replacement battery came with a clear protective film that should be removed before installation. Be sure not to overlook the film on the bottom of the battery as it covers only a portion of that side and might be easy to overlook.

Do not over-tighten the bolts holding the battery in place. One of the tabs on the original battery was broken, presumably due to over-tightening.

Patrick Langvardt - Réponse

Is it possible to use the trackpad from MacBook Unibody Model A1278 in this macbook pro?

Ralf Justinger - Réponse

  • Avec l'extrémité plate d'une spatule (spudger), faites levier sur le connecteur du pavé tactile pour le débrancher de sa prise sur la carte mère.

Ajouter un commentaire

  • Ouvrez votre MacBook Pro et posez-le sur une table comme sur la photo.

Ajouter un commentaire

  • Pendant que vous maintenez d'une main le bord du pavé tactile le plus proche possible de la carte mère, dévissez les quatre vis cruciformes de 1,2 mm entourées en rouge.

I ordered some tools from iFixit for replacement of the trackpad but the Phillips #00 Screwdriver named above is still too big for the (tiny) screws of the trackpad. Shouldn't that be a Philips #000?

sleutelman - Réponse

I have a macbook pro 15 inch unibody from 2010-2011, do you think it would work to use that trackpad as an replacement for my 13 inch 2012-2013

Filip - Réponse

A word of caution if you are replacing your trackpad due to a bulging battery. This guide assumes that the original mounting tabs are not damaged and it does not look like the iFixit trackpad replacement kit comes with new tabs. My MBP had a bulging battery, which pushed up on the bottom of my trackpad, deforming one of these tabs. Now that I have removed the battery, the trackpad still works, but it is not flush with the case and the physical clicks are not as responsive as I would like. Does iFixit sell just the replacement tabs?

Matt Marchese - Réponse

Same here luckily the trackpad still works but the taps have deformed. Anyone find a place to pick up just those tabs? Edit: found them MacBook Pro Unibody (Mid 2009 through Mid 2012) Trackpad Mounting Screws

iAndrewC -

Be careful with this step. The very tiny screws are very hard to remove with a #00 screwdriver. I tried with mine and I mashed the srews heads, it was then very very hard to remove it. Better to use a #000 screwdriver. If the heads are mashed like me, I suggest you use a 0.1 flat screwdriver, it worked well in my case.

Jonathan - Réponse

I couldn't even begin to use the #000 as the edges were not deep or narrow enough for the condition of the screws from factory install. The .1 flat screwdriver worked like a charm though and didn't mess up the screws further at all. I was getting nervous that I'd need to get another screwdriver beyond what's in the iFixit toolkit, but this worked as a better solution.

Thom Merrick -

I used the J000 head from the iFixit kit and it fit pretty snug, and the screws came out very cleanly

andrew - Réponse

  • Si nécessaire, délogez soigneusement le bord du pavé tactile le plus proche du clavier de son emplacement dans le boîtier supérieur en l'éloignant des fixations attachées au boîtier supérieur.

  • Poussez soigneusement le connecteur et la nappe du pavé tactile à travers la fente dans le boîtier supérieur.

  • Il est peut-être nécessaire d'utiliser une spatule pour aider le connecteur du pavé tactile à passer à côté du bord de la carte mère.

  • Une fois que la nappe est complètement enlevée de sa fente dans le boîtier supérieur, éloignez le pavé tactile du bord extérieur du boîtier supérieur et ôtez-le de l'ordinateur.

Ajouter un commentaire

  • Lors de l'installation de votre nouveau pavé tactile, il peut être difficile de faire passer la nappe à travers le boîtier supérieur puis à côté de la carte mère. La pointe d'une spatule peut vous aider à guider le connecteur à côté de la carte mère pendant que vous poussez la nappe à travers sa fente dans le boîtier supérieur de l'autre main.

This article seems to be about REPLACING a trackpad. Why does the summary claim that no parts are needed?

Sam Pittman - Réponse

If your replacement trackpad comes with the cable separated and loose, the connection to the trackpad needs to have a tab pressed down which keeps the connection snug. It won't work without it. It's a tab on the trackpad part of the connection. Tab might be the wrong word; the connection has to be in all the way, then clamp it closed with the tab... oops! LOL

Mark - Réponse

  • Ensuite, remettez les quatre vis cruciformes de 1,2 mm le long du bord intérieur du pavé tactile.

  • Serrez complètement les vis, puis desserrez-les d'un quart de tour.

  • Vérifiez l'alignement du pavé tactile du côté clavier du boîtier supérieur. Une fois que vous avez centré le pavé tactile dans le boîtier supérieur, serrez complètement les quatre vis cruciformes.

trackpad still doesn't click. I've tried two separate parts.. but what makes it pop back up after depressing the pad? It just lays there. I've taken it apart four times to adjust the tork screw... nothing. HELP!

Gail - Réponse

My trackpad was driving me up the wall, bouncing all over the place. Ifixit Trackpad comes with extra screws, hinge and adjuster. You won't believe how tiny these screws are! If one falls in the carpet-it's GONE! Bless you Ifixit! To center when re-installing adjust by sliding a thin piece of paper (scotch tape?), under bottom of trackpad, let Trackpad rest on it's own weight and then tighten one top and bottom screw a little bit, and eyeball it, just the tiniest crack of daylight on each side. I strongly suggest the highest quality magnetic screwdriver you can find. The little torx screw disc is an adjuster. If too tight, trackpad won't 'click.' On a Mac, click is not really essential as long as tap and slide are working right. Needs a small amount of clearance. When properly installed you can 'feel' the click if it's right. Probably won't need to mess with it at all. Now my trackpad works like it should, I am a happy camper!

ovenwally - Réponse

I replaced the trackpad with a new one: the arrow moves but was not possible to click. I putted back the old trackpad and it works with. The solution: the eleventh picture shown a gray Torx type screw to the left of the connector where there is the recess in the back of the mouse. This screw is used to increase or decrease the depth of clicks. in my case it was too screwed and it was as if I held continually pressed the truckpad: therefore, it was enough to loosen it. At this point I ask myself since in the old truckpad I had problems with the physical click, I probably would have been enough to adjust the screw.

caronte88 - Réponse

Vielen Dank, dies hat mir sehr beholfen :-)

Frederik Häger -

ifitit is once again amazing. My trackpad just stopped working on my four year old machine. Bought a new trackpad from iFitit, followed the guide and now I have a functional laptop again. One thing to note. 1.2mm is small very, very small. The screws for the trackpad *will* get lost if they fall of the table. Make sure that doesn't happen.

Jerry - Réponse

I was having trackpad issue on my 2010 machine, did the replacement from ifixit which arrived broken (bummer) but they replaced it no problems. It worked great for just under a year but now I'm having the same issues again of poor finger tacking, jumping, and lack of sensitivity. I've tried cleaning the whole unit, rebooting in safe mode, refreshing code, and anything else the web has provided. I'm starting to wonder if it's something else on my machine or if the trackpads just don't hold up well enough. Overall I'm super frustrated to have a newer pad crap out this early.

eastern117 - Réponse

I don't have a magnetic head driver so I had a terrible time trying to get the screws in. I found getting the screw on the table Phillips side up, I pushed my finger tip into the head til it stuck and placed the screw into the thread that way. The screw stayed in long enough for me to tighten with the driver ! Oh, what a relief! I only lost one screw; thank god for replacement screws! Order your trackpad with screws! They fall and get lost easy! Now I'm happy! :)

Mark - Réponse

Next time rub the tip of the screwdriver against a magnet about 10-20 times in the SAME direction (A fridge magnet works)

Karan Kakkar -

For some reason the black material under the tabs were enough to stop the track pad from being able to click. I removed that material and now have a track pad that clicks.

blrmisc - Réponse

I installed the trackpad, but it was not behaving correctly. Took it apart again and reinstalled, using the 2 new foils that go under the trackpad keeper screws (my old ones were kind of mangled, probably from all the force I had to use on the old trackpad). I also made extra sure the trackpad was precisely lined up this time. Voila! A nice, sensitive new trackpad.

Thanks, iFixit!

Felix - Réponse

Türkçe yardımcı olabilecek kimse var mı?

Volkan Ogul - Réponse

Conclusion

Pour remonter votre ordinateur, suivez ces étapes dans l'ordre inverse.

126 autre(s) ont terminé cette réparation.

Merci à ces traducteurs :

100%

Claire Rapp nous aide à réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›

10 commentaires

I couldn't be more pleased with myself or ifixit right now. I went to the Apple service centre to find out about getting my trackpad fixed and was told it would take 2 weeks to diagnose what the problem was and up to another 2 weeks before they could fix it. Luckily, I stumbled upon ifixit - got a tool pack and parts delivered in 5 days and I was just able to replace the trackpad easily in 30 minutes. I did find that I wasn't able to get the screws from the back of the trackpad out with the Phillips 00 screwdriver though - I had to use the 000. I am weirdly looking forward to something else breaking now just so I can fix it:-)

rebeccanorris - Réponse

Why did I not do this earlier! I wasted 2 years of my laptop life struggling with the trackpad and external mouses. This was pretty easy.

Omkar Danke - Réponse

I just completed this very carefully following every step to replace a track pad that worked but was shattered. I put it all back together but the track pad didn't work. I thought it was a bad track pad so a i put the old one back in. Still the mouse it frozen to the corner not responding at all. now what?!

Jonathan Eyestone - Réponse

Just installed my new trackpad and it works like a dream. Thanks!!

Judy MacDonald - Réponse

Thanks!! This worked perfectly. (Almost... I stripped a couple tiny screws on the trackpad before it was perfectly placed so I have a dead spot about the size of a quarter in the upper right corner where it won't click, but it's much better than the previous one.)

patrisha.wells - Réponse

I was scared to this project until I found this site! I've never opened up any of my computers until now and this manual made it so easy!

Rachel Wilkosz - Réponse

Awesome! Such clear instructions, in the end it was so easy.

Derek van Someren - Réponse

My replacement part (third party) did not fit quite right. I found the clicker was depressed upon installation. I was also unable to loosen the clicker screw (not sure why it was so tight). I was successful trimming some plastic off the trackpad clicker which did the trick!

emholden - Réponse

I had a fairly rough drop of my Macbook Pro recently. Ordered new glass for the screen and the necessary tools since that appears to be the only part that “needs” to be replaced since everything else seems to work. The one thing I noticed is the trackpad is raised up above the body of the computer in certain spots. If I attempt to lightly push it back down it just pops up on the diagonal corner. Does anyone think I’ll need to order any additional material before I open the computer (as I’d like to only get into it once) or is it just the tabs the trackpad is screwed into being bent?

lcubbin - Réponse

As you can see in the photo for step 10, the trackpad is held with screws that attach along the side of the trackpad that is adjacent to the spacebar. The other long side is held by the two tabs along the bottom. Once you open up the computer you may find that one of the tabs on the trackpad is bent/broken, or that some supporting part of the lower case is cracked. As far as I know, there’s no easy way to tell until you get in there — sorry.

One other thing that you may find once you get inside is that your battery has started to swell. The battery is directly beneath the trackpad, and when it swells it pushes up on the underside of the trackpad. Since the battery may not swell evenly, this may create a high spot that the trackpad teeters on when you’re pressing on it. Another symptom of a swelling battery will be if the trackpad works intermittently or only in some areas, or will track but won’t click. This will require replacing the battery - which if it has started to swell, you want to do anyway.

captainvector -

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 38

7 derniers jours : 240

30 derniers jours : 987

Total : 109,316