Remplacer un ventilateur défectueux est extrêmement simple et évitera à votre ordinateur de surchauffer. Dans ce tutoriel, il s'agit du ventilateur du côté droit du MacBook en mode de travail. Pendant la procédure de remplacement, ce ventilateur sera à votre gauche.

  1. Boîtier fermé, placez l'Unibody à l'envers sur une surface plane.
    • Boîtier fermé, placez l'Unibody à l'envers sur une surface plane.

    • Appuyez sur le côté rainuré du loquet de déverrouillage de la trappe d'accès de manière à saisir l'extrémité libre du loquet. Soulevez le loquet de déverrouillage à la verticale.

    The A1286 has no Access Door.!!

    I actually can see no sign of the battery!...

    aguib - Réponse

    Quote from aguib:

    The A1286 has no Access Door.!!

    I actually can see no sign of the battery!...

    I assume you have the newer model, with the built-in battery. It's still removable with tools, but these are the wrong instructions for that model.

    lgc90 - Réponse

    when will there be a guide for the other unibody macbook pro. that does not have an access door?

    irishking - Réponse

    Is there a manual to show, how disasembly the display, i mean, after step 5, to check the display between lcd and aluminiun back case?


    Max - Réponse

    On other guides you state the height of the HD that can be supported, e.g. MacBook Pro 15" Core 2 Duo Model A1211 Hard Drive Replacement , I have read ( but have not confirmed ) that the uni-body MacBook Pro can be fitted with the 750GB and 1TB 12mm drive from Western Digital.

    Can you confirm this?

    Many thanks in advance.

    ahothabeth - Réponse

    Citation de SHerwood Ball :

    My display and aluminum casing has separated.

    I don't know if it just snaps back together or does it need to be glued.

    I dropped mine on the carpeted stairs and the display still works.

    I'm hoping I can just snap it back together and that no plastic pieces or teeth of the snapping

    portion have been broken........

    SHerwood Ball - Réponse

    When you say "left fan" is this "left when looking at the logic board after turning the computer over and looking it up opening it up" or "left when sitting at the computer keyboard and typing on it"?

    thvv - Réponse

    We always use left and right in reference to the computer when you're using it.

    Andrew Optimus Goldberg -

    Directions were great and the worn dc in board was replaced. The hardest part of the procedure is disconnecting the data display cable. A better description of step 21 is to slide the connector parallel to the circuit board towards the outside corner. Reconnecting correctly took several tries.

    I used the tip of the spudger to nudge the corners a little at a time to seat the connector.

    The ribbon connector for the keyboard has to be inserted all the way before seating the retaining cap. It took me three tries . First try power button did not work second try numbers keys did not work.

    Thanks for the directions ...could not have done it with out them!!!

    landryd - Réponse

    Hola. Poseo un MacBook Pro Late 2008 y debo cambiarle las cornetas. Me sirve unas cornetas de un MBP Late 2011?

    jegonzalez80 - Réponse

  2. La trappe d'accès est à présent suffisamment relevée pour la basculer et la retirer de l'Unibody.
    • La trappe d'accès est à présent suffisamment relevée pour la basculer et la retirer de l'Unibody.

    Ajouter un commentaire

    • Assurez-vous que la languette de la trappe d'accès est bien à la verticale avant de commencer.

    • Tirez sur la languette et retirez la batterie de votre MacBook.

    • Si la languette n'est pas bien positionnée, elle empêchera la batterie de sortir.

    Do I need to wait for the battery to charge completely before using the computer (while plugged in)?

    Kaila Potts - Réponse

    No. You do not need to charge it completely before removing it.

    Titus (#1579) - Réponse

  3. Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • Retirez les huit vis suivantes par lesquelles le boîtier inférieur est fixé au châssis :

      • Une vis Phillips 5,4 mm.

      • Trois vis Phillips 14 mm.

      • Quatre vis Phillips 3,5 mm.

    Hi, My name is Jess I need help asap I accidentally dropped my macbook Pro and i cant find the silver screw for the top left back side, Does any one know if I can replace it with an eye glass screw?? If you can help at all Please e-mail me at thx please help me my bf is going off... ;(

    Jess - Réponse

    The fixit PH00 is the wrong screw driver for this entire job. It did not fit in the screws, it was too pointy and caused screws to be rounded off.

    mattrittgers - Réponse

    • En vous servant des deux mains, soulevez le boîtier inférieur et retirez-le du boîtier supérieur.

    About midway along each edge is a snap. To release each snap, gently slide the flat edge of a Spudger under the lower case, then lift the lower case away.

    jonathansturges - Réponse

    I have an late 08 macbook pro and replaced my cd drive with a hd caddy and hard drive put in it. everything works but my wifi is saying no hardware installed. Bluetooth and camera working just the wifi isn't. Everything was working just find before i did this but now i cant get my wifi back on. I checked the cable looks to be inserted properly any one else had this happen or have any solutions ?

    myjellio - Réponse

    Having the same problem after this step with wifi not working anymore - it says “no airport card installed”… Any suggestions/fixes?

    David Lassiter - Réponse

    • Avec une spatule (spudger), soulevez le connecteur du ventilateur pour le débrancher de la carte mère.

    • Veillez à seulement faire levier sur le connecteur lui-même et non sur la prise ou vous risquez d'endommager le dispositif.

    • Il est utile de faire pivoter la spatule en dessous des câbles du ventilateur pour débrancher le connecteur.

    Did it the way described. Maybe because of the age of the Mac/circuit board but the sockets came out with the connector. Only solution now for this fan to work would be to hard solder. Not a happy outcome.

    Nicole Bokat - Réponse

    • Dévissez les trois vis suivantes fixant le ventilateur droit au boîtier supérieur et à la carte mère :

      • Deux vis cruciformes de 3,2 mm.

      • Une vis cruciforme de 3,5 mm.

    I ruined the head of the heads of the 3.2 mm and the 3.5 Phillips screws. What kind of screws are this (M1, M1.2, ...?)? I need a replacement.

    PS I used the appropriate screw driver (Wiha PH00).

    Michael Domhardt - Réponse

    Hi! how did you fix it? I ruined the last two red 3,2 mm screws as well, so the old fan is still in there....

    laurabaas94 -

    I can't seem to get the two (2) 3.2 screws out, they are in way too tight. I'm afraid of rounding out the slots and putting too much pressure on the board. No issues with replacing the other fan..any hints/tricks to getting these screws out? thanks

    Joseph Vossen - Réponse

    • Ôtez le ventilateur du boîtier supérieur.

    Ajouter un commentaire


Pour remonter votre ordinateur, suivez les instructions dans le sens inverse.

68 autre(s) ont terminé cette réparation.

Merci à ces traducteurs :


Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›

A great walkthrough.

Once completed, I did a reset of the PRAM, and it all worked beautifully.

Thanks again.

Shai Yammanee - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 4

7 derniers jours : 12

30 derniers jours : 74

Total : 38,783