Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Boîtier fermé, placez l'Unibody à l'envers sur une surface plane.
-
Appuyez sur le côté rainuré du loquet de déverrouillage de la trappe d'accès de manière à saisir l'extrémité libre du loquet. Soulevez le loquet de déverrouillage à la verticale.
-
-
-
Tirez sur la languette et retirez la batterie de votre MacBook.
-
Si la languette n'est pas bien positionnée, elle empêchera la batterie de sortir.
-
-
-
Retirez les huit vis suivantes par lesquelles le boîtier inférieur est fixé au châssis :
-
Une vis Phillips 5,4 mm.
-
Trois vis Phillips 14 mm.
-
Quatre vis Phillips 3,5 mm.
-
-
-
Dévissez les 5 vis suivantes, fixant la paroi interne au boîtier supérieur :
-
Trois vis cruciformes de 10,5 mm.
-
Deux vis cruciformes de 3,7 mm.
-
-
-
Retirez les six vis suivantes fixant le ventilateur droit et le ventilateur gauche à la carte mère :
-
Quatre vis cruciformes de 3,5 mm.
-
Deux vis cruciformes de 3,2 mm.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove three 2 mm Phillips screws securing the battery connector cover to the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the battery connector cover out of the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel the battery connector cable off the adhesive securing it to the upper case.
-
De-route the battery connector cable through the gap in the upper case and remove it from the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following screws securing the ExpressCard Cage to the upper case:
-
Two 4 mm Phillips screws.
-
Two 1.9 mm Phillips screws.
-
Lift the the ExpressCard Cage out of the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single Phillips screw securing the hard drive bracket to the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the hard drive by its pull tab enough to grab and remove the retaining bracket.
-
Lift the hard drive out of the upper case, minding the cable attaching it to the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the hard drive from its cable by pulling the cable connector straight away from the drive.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following three Phillips screws securing the optical drive to the upper case:
-
One 3.5 mm Phillips screw.
-
Two 2.5 mm Phillips screws.
-
Lift the optical drive from its right edge and pull it out of the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following four screws securing the subwoofer and right speaker to the upper case:
-
Two 3.2 mm Phillips screws.
-
One 2.6 mm Phillips screw.
-
One 5.0 mm Phillips screw.
-
Lift the subwoofer and right speaker assembly out of the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel the hard drive cable from the adhesive securing it to the upper case, and maneuver the plastic retaining block out of the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove two 8 mm Phillips screws securing the camera cable bracket to the upper case.
-
Seperate the camera cable bracket from the camera cable and remove it from the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the 7 mm Phillips screw from the LVDS cable bracket.
-
Lift the LVDS cable bracket out of the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove two outer 6 mm T6 Torx screws securing each side of the display to the upper case (4 screws total).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Open your MacBook Pro so the display is perpendicular to the upper case.
-
Place your opened MacBook Pro on a table as pictured.
-
While holding the display and upper case together with your other hand, remove the 6 mm Torx screw from the lower display bracket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the last remaining 6 mm Torx screw securing the display to the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case.
-
Rotate the display slightly away from the upper case.
-
Lift the display away from the upper case, minding any brackets or cables that may get caught.
-
Annulation : je n'ai pas terminé ce tutoriel.
45 autres ont terminé cette réparation.
2 commentaires
Thanks Dan. The T6 Torx screwdriver is now part of the required tools list.