Réparez vos affaires Communauté Boutique

Ce tutoriel a des changements plus récents. Passer à la dernière version non vérifiée.

MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement

Introduction

Use this guide to replace a non-functioning Bluetooth board in the Anti-Glare option of the Mid 2009 MacBook Pro.

The Glossy display option does not have this display-mounted bluetooth card, it is found under the clutch cover.

Ce dont vous avez besoin

  1. MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement, Lower Case: étape 1, image 1 de 1

    • Remove the following ten screws securing the lower case to the upper case:

    • Seven 3 mm Phillips screws.

    • Three 13.5 mm Phillips screws.

    Traduire

  2. MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement: étape 2, image 1 de 2 MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement: étape 2, image 2 de 2

    • Using both hands, lift the lower case near the vent to pop it off two clips securing it to the upper case.

    • Remove the lower case and set it aside.

    Traduire

  4. MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement, (Anti-Glare Option) Bluetooth Board: étape 3, image 1 de 2 MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement, (Anti-Glare Option) Bluetooth Board: étape 3, image 2 de 2

    • Disconnect the Bluetooth cable by pulling the male end straight away from its socket.

    • Pull the connector parallel to the face of the logic board, not straight up.

    • Use the flat end of a spudger to pry the Bluetooth antenna cable from its socket on the board.

    Traduire

  5. MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement: étape 4, image 1 de 2 MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement: étape 4, image 2 de 2

    • Remove the two 8 mm Phillips screws securing the Bluetooth/camera cable retainer to the upper case.

    • One of the screws may remain captive in the Bluetooth/camera cable ground loop. If replacing the display, be sure to transfer this screw to the new unit.

    • Lift the Bluetooth board/cable retainer assembly out of the upper case.

    Traduire

  6. MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement, (Anti-Glare Option) Bluetooth Board: étape 5, image 1 de 1

    • Remove the single Phillips screw securing the Bluetooth board to the retainer.

    • Lift the Bluetooth board off the retainer.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

3 autres ont terminé cette réparation.

4 commentaires

is there a newer bluetoth 4.0 / 4.1 board available for the mid 2009 15'' model?

roblamper - Réponse

I second roblamper's question... Yosemite/iOS 8's new "Handoff" as well as "OS X+iOS AirDrop" feature(s) appear to be thwarted on the Mid 2009 MBP due to the existing Bluetooth hardware limitation. I suppose even if there is a Bluetooth 4.0 LE replacement available there may be some .kext changes required. Regardless, baby steps... First things first and that is discovering suitable hardware (-;

honDA9xsi - Réponse

Does anyone know where the bluetooth board for a NON ANTI-GLARE model might be found? I'm presuming that I have to lift the logic board to get to it as I can't see anything from the underside.

Hope you can help!

Thanks

John

jpmolesworth - Réponse

Where do i find that Cable?

pkremsi - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 4

30 derniers jours : 14

Total : 17,673