Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. , Batterie: étape 1, image 1 de 1
    • Utilisez vos doigts pour pousser les deux onglets de libération de la batterie et retirez la batterie de l'ordinateur.

  2. , Trappe de la mémoire: étape 2, image 1 de 1
    • Retirez les quatre vis Phillips 3,4 mm identiques à partir de la trappe de la mémoire. Ces vis ont 4 mm de diamètre de tête au lieu de 3 mm sur les vis du corps.

  3. : étape 3, image 1 de 1
    • Soulevez la trappe de la mémoire assez pour pouvoir la saisir, faites-la glisser vers vous pour la tirer loin du boitier.

  4. , Boîtier supérieur: étape 4, image 1 de 1
    • Retirez les trois vis cruciformes situées dans le compartiment de la batterie, près du loquet. Apple a eu la gentillesse d'incliner légèrement ces vis pour les rendre plus faciles à retirer. Sur le A1261, ces vis ont des têtes de 4 mm de diamètre au lieu des têtes de 3 mm des vis restantes.

  5. : étape 5, image 1 de 1
    • Retirez les six vis suivantes :

    • Deux vis Torx T6 de 14,5 mm de part et d'autre du compartiment de la RAM.

    • Quatre vis cruciformes de 3,4 mm le long de la charnière.

  6. : étape 6, image 1 de 1
    • Retirez les quatre vis cruciformes de 3,4 mm sur le côté des ports de l'ordinateur.

  7. : étape 7, image 1 de 1
    • Faites pivoter l'ordinateur de 90 degrés et retirez les deux vis cruciformes à l'arrière de l'ordinateur.

  8. : étape 8, image 1 de 1
    • Faites de nouveau pivoter l'ordinateur de 90 degrés et retirez les quatre vis cruciformes sur le côté de l'ordinateur.

  9. : étape 9, image 1 de 1
    • Ne retirez pas le boîtier supérieur d'un coup sec. Le boîtier est relié à la carte mère par une nappe.

    • Soulevez l'arrière du boîtier et faites glisser vos doigts le long des côtés, en détachant le boîtier au fur et à mesure. Une fois que vous avez détaché les côtés, vous devrez peut-être faire basculer le boîtier de haut en bas pour détacher l'avant du boîtier supérieur.

  10. : étape 10, image 1 de 1
    • Débranchez la nappe du pavé tactile et du clavier de sa prise sur la carte mère.

    • Retirez le boîtier supérieur.

  11. , Lecteur optique: étape 11, image 1 de 1
    • Déconnectez la nappe orange SuperDrive de la carte mère, en retirant le ruban adhésif si nécessaire.

  12. : étape 12, image 1 de 1
    • Retirez les trois vis suivantes :

    • Deux vis Torx T6 noires de 4 mm de chaque côté du SuperDrive.

    • Une vis Torx T6 argentée de 8,7 mm (noire sur certains modèles) à l'arrière du lecteur, près du haut-parleur.

  13. : étape 13, image 1 de 1
    • Utilisez une main pour tirer le câble du haut-parleur vers l'arrière et utilisez votre autre main pour soulever le lecteur optique et le sortir de l'ordinateur.

    • Si un CD ou tout autre objet est coincé dans votre lecteur optique, nous avons un tutoriel de réparation des lecteurs optiques.

  14. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 14, image 1 de 3 : étape 14, image 2 de 3 : étape 14, image 3 de 3
    • Disconnect the ten indicated connectors from the logic board.

    • The connectors have different positions for the four MacBook Pro revisions covered by this guide, and their locations are highlighted in the three pictures on this step.

  15. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 15, image 1 de 1
    • Rotate the large display data cable to the left and disconnect the small right thermal sensor cable beneath.

    • If you have the A1261 model, the right thermal sensor cable is located in between the right fan connector and display data cable.

  16. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 16, image 1 de 1
    • Remove the single black 4 mm T6 Torx screw securing the clear plastic shield over the right ambient light sensor.

    • Lift the clear plastic shield off the right ambient light sensor.

  17. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 17, image 1 de 1
    • Peel up the orange Kapton tape securing the left thermal sensor cable to the logic board.

    • If you have a MacBook Pro 17" Model A1229, this is the middle thermal sensor.

  18. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 18, image 1 de 1
    • Remove the following twelve screws:

    • Seven 6.5 mm T6 Torx screws.

    • Two shanked 7.6 mm T6 Torx screws securing the battery connector to the lower case.

    • Three 7.8 mm T6 Torx screws.

  19. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 19, image 1 de 1
    • Lift up the left side of the logic board and disconnect the multi-colored power connector from the bottom of the board.

  20. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 20, image 1 de 1
    • Grasp the logic board at the left side and at the thin section near the right fan, and rotate the logic board out of the lower case.

  21. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 21, image 1 de 1
    • If the right speaker assembly remains attached to the logic board, hold the logic board with one hand and slide the speaker up slightly to free it from the logic board.

    • To properly reassemble your MacBook Pro, you'll have to clean off and replace the thermal compound from the three chips on the underside of the logic board. Use our Applying Thermal Paste Guide to prepare the processor and heat sink surfaces.

  22. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 22, image 1 de 3 : étape 22, image 2 de 3 : étape 22, image 3 de 3
    • Disconnect the two antenna cables attached to the AirPort Extreme card.

    • The cable with the gray shielding attaches to the left side connector, while the cable with the white shielding attaches to the right side.

    • If you have a MacBook Pro 17" Model A1229, there are three antenna cables attached to the AirPort Extreme card instead of two.

    • If you have a MacBook Pro 17” Model A1261 the cable with the black shielding attaches to the left side of the connector, while the cable with blue shielding attaches to the right side. The gray cable isunattached and the end covered.

  23. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 23, image 1 de 1
    • Remove the single black 4 mm T6 Torx screw from the top right corner of the AirPort Extreme card.

  24. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 24, image 1 de 1
    • Lift the AirPort Extreme card up and slide it out of its connector.

  25. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 25, image 1 de 1
    • Remove the two 7.8 mm silver T6 Torx screws from the top left and bottom right corners of the left speaker assembly.

    • The magnet in the MagSafe connector may pull the upper screw towards it after the screw has been freed.

  26. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 26, image 1 de 1
    • Lift up on the left speaker assembly and rotate it slightly. It is not possible to entirely remove the speaker yet, as it is still connected to the left I/O board beneath.

  27. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 27, image 1 de 1
    • Disconnect the right speaker from the left I/O board. Make sure to pull on the top section of the white connector, not the cable itself.

  28. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 28, image 1 de 1
    • Lift the right speaker assembly out of the computer.

  29. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 29, image 1 de 1
    • If tape is attaching the attenda cable bundle to the left speaker assembly remove it.

    • Disconnect the two cables attaching the left speaker assembly to the left I/O board.

  30. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 30, image 1 de 1
    • Peel up the iSight and inverter cables which are attached with a mild adhesive above the left fan.

  31. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 31, image 1 de 1
    • Remove the five 7.8 mm T6 Torx screws securing the fans to the lower case.

  32. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 32, image 1 de 1
    • Lift the heat sink and attached fans out of the computer.

    • If you are replacing the heat sink, be sure to transfer the attached thermal sensor to your new heat sink.

    • If you need to mount the heat sink back into the laptop, we have a thermal paste guide that makes replacing the thermal compound easy.

    • Now is a good time to lean the fans back and clean out any dust bunnies from the grill. Also clean any dried thermal paste from the heat sink contact pads.

Ligne d'arrivée

17 autres ont terminé cette réparation.

iRobot

Membre depuis le 09/24/09

1 Réputation

636 tutoriels rédigés

3 commentaires

Does anyone know if it is possible to remove and replace the motherboard and heat sink without detaching the heat sink? I sent out my mobo to be reballed and they returned it with a heat sink attached and would not honor their warranty if I separated the two, and they assured me it could be done.

thanks for any help

maccentric - Réponse

Sadly that is not possible. In order to remove the Heat Sink, you have to remove the Logic Board first. Also the speaker system and other parts are in between the Heat Sink and the Logic board, and you can't just pop the Heat Sink in with the Logic Board attached due to the port slots on the right side. To be honest with you, the fact that they reballed your board and shipped it with the Heat Sink attached, is very unusual? Especially for this model. It would work for other Logic Boards where the Heat Sink is actually screwed directly onto the Logic Board. If they assured you that it can be done, ask them to show you how to do it.

Maximilian Willert -

Thanks a lot for this guide! I used this guide to install new thermal paste. By far one of the more difficult operations i've done so far. My advise is to really take your time for this one and not rush anything at all. This model is now almost 10 years old but it still runs!

Maximilian Willert -

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 3

30 derniers jours : 19

Total : 25,827