Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. , Boîtier inférieur: étape 1, image 1 de 1
    • Retirez les huit vis Phillips 4 mm par lesquelles le boîtier inférieur est fixé au MacBook.

  2. : étape 2, image 1 de 3 : étape 2, image 2 de 3 : étape 2, image 3 de 3
    • Le boîtier inférieur est construit en aluminium avec un revêtement en caoutchouc. Ne pliez pas trop l'aluminium lors du retrait, car une déformation permanente générerait des problèmes de tolérance après le remontage.

    • Soulevez légèrement le boîtier arrière au niveau de la fente.

    • Continuez à faire courir vos doigts entre les boîtiers inférieur et supérieur jusqu'à ce que le boîtier supérieur se dégage des clips de fixation.

    • La position de ces trois clips est indiquée dans la troisième photographie.

  3. , Batterie: étape 3, image 1 de 1
    • Pour des raisons de précaution, nous conseillons de déconnecter le connecteur de la batterie de la carte mère pour éviter une décharge électrique. Cette étape est facultative et non obligatoire.

    • Avec l'extrémité plate d'une spatule (spudger), soulevez le connecteur de la batterie de sa prise sur la carte mère.

    • Il est peut-être plus facile de soulever les deux côtés du connecteur avec vos ongles.

  4. , Grille d'aération arrière: étape 4, image 1 de 1
    • Retirez les vis suivantes de la grille d'aération arrière, du côté du lecteur optique :

    • Deux vis Torx T8 10 mm

    • Deux vis Phillips 5 mm

  5. : étape 5, image 1 de 1
    • Retirez les vis suivantes de la grille d'aération arrière, du côté du port :

    • Deux vis Torx T8 10 mm

    • Deux vis Phillips 5 mm

  6. : étape 6, image 1 de 1
    • Sortez avec précaution la grille d'aération arrière du boîtier supérieur.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 1
    • Remove the single 3 mm Phillips screw securing the AirPort/Bluetooth antenna ground strap to the rear speaker.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 8, image 1 de 2 : étape 8, image 2 de 2
    • Use the tip of a spudger to pry the AirPort and Bluetooth antenna connectors (3 total) up off the AirPort/Bluetooth card.

    • De-route the long antenna from its channel in the rear speaker housing.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 9, image 1 de 2 : étape 9, image 2 de 2
    • Grab the plastic pull tab secured to the display data cable lock and rotate it toward the DC-In side of the computer.

    • There is also a thin metal lock clip under the plastic tab that has to be released ( Use the tip of a spudger ) before you can disconnect the display data cable.

  10. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 10, image 1 de 2 : étape 10, image 2 de 2
    • Gently pull the display data cable connector away from its socket on the logic board.

    • Pull the socket parallel to the face of the logic board.

    • The display data cable socket is made of very thin metal and is easily bent. Be sure to pull the connector straight away from its socket.

  11. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 11, image 1 de 1
    • Open your MacBook so the display is perpendicular to the upper case.

    • Place your opened MacBook on a table as pictured.

    • While holding the display and upper case together with your left hand, remove the remaining 7.8 mm with lock washer T8 Torx screw from the lower display bracket.

  12. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 12, image 1 de 1
    • Be sure to hold the display and upper case together with your left hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component.

    • Remove the last remaining T8 Torx screw securing the display to the upper case.

  13. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 13, image 1 de 2 : étape 13, image 2 de 2
    • Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case.

    • The display data cable may cause the upper display bracket to get caught on the upper case. It may be helpful to slightly rotate the upper case away from the display for more clearance.

    • Rotate the display slightly away from the upper case.

  14. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 14, image 1 de 1
    • Lift the display up and away from the upper case, minding any brackets or cables that may get caught.

  15. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 15, image 1 de 3 : étape 15, image 2 de 3 : étape 15, image 3 de 3
    • Insert the flat end of a spudger between the thin rubber strip surrounding the front display bezel and the rear display bezel.

    • Do not try to insert the spudger between the thin rubber strip and the plastic face of the front display bezel.

    • Use the flat end of your spudger to carefully pry the front display bezel away from the adhesive securing it to the rear display bezel.

    • Do not pry against the fragile glass LCD panel. Also, do not excessively bend the plastic as it may permanently deform.

    • Continue prying until the front display bezel is free along the right side of the display and behind the right clutch hinge.

  16. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 16, image 1 de 2 : étape 16, image 2 de 2
    • Use the flat end of a spudger to pry the front display bezel off the top edge of the display assembly.

    • It may be helpful to insert and twist the flat end of your spudger to enlarge the gap between the front & rear display bezels as you work your way around the edge of the display.

    • Continue separating until the top edge of the front display bezel is free from the display assembly.

    • Be careful when prying near the iSight camera board, as it has exposed circuitry and is delicate.

  17. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 17, image 1 de 2 : étape 17, image 2 de 2
    • Use your spudger to pry the left side of the front display bezel away from the display assembly.

    • Carefully pry up the area behind the left clutch hinge.

    • During reassembly, be sure the small plastic pegs on the front display bezel mate up with the holes in the rear display bezel (shown in red). Failure to do so will prevent the front display bezel from sitting flush against the rear bezel.

  18. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 18, image 1 de 3 : étape 18, image 2 de 3 : étape 18, image 3 de 3
    • Slowly work your way across the lower edge of the front display bezel until it is free from the display assembly.

    • Be sure to pry up as far away from the LCD as possible, as it extends below the edge of the front display bezel.

    • When you get about half way across, pry up from the other side of the front display bezel's lower edge to ease the process.

  19. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 19, image 1 de 1
    • Remove the front display bezel from the display assembly.

    • To help the adhesive avoid losing is tackiness, do not excessively handle the adhesive and be sure to keep it clean until you are ready for installation.

  20. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 20, image 1 de 1
    • Remove the two 3 mm Phillips screws securing the clutch cover to the rear display bezel.

  21. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 21, image 1 de 3 : étape 21, image 2 de 3 : étape 21, image 3 de 3
    • Insert the flat end of a spudger into the open end of the clutch cover and pry up to release it from the rear display bezel.

    • Pry up from both sides of the clutch cover until it is completely free from the display assembly.

  22. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 22, image 1 de 1
    • Remove the clutch cover from the display assembly.

Ligne d'arrivée

13 autres ont terminé cette réparation.

2 commentaires

Plz plz if you explain how to fix any devices from first plz end it to close again , because some devices unable to close like apple wireless keyboard when i try to open ok good put when i try to close it not good .

and plz make to every process video because some process not Clear

" thx for understand" and very good work .

Fady - Réponse

The white screen gasket (trim) on my MacBook A1342 is peeling off. How do I insert it back? It keeps peeling back off even when I insert it back. It only happens at one specific spot. I don't want to replace the trim. I just want to glue it back in. What kind of glue may I use?

Dario Meze - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 10

Total : 15,499