Aller au contenu principal

Ce dont vous avez besoin

  1. Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the back cover: étape 1, image 1 de 3 Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the back cover: étape 1, image 2 de 3 Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the back cover: étape 1, image 3 de 3
    • Power off your phone before beginning disassembly.

    • Insert the edge of the spudger into the notch on the bottom right corner of the phone.

    • Twist the spudger to start releasing the back cover from the phone.

    • Slide the spudger along the bottom edge to separate the back cover from the phone.

  2. Motorola Moto E4 Plus LCD and Digitizer Replacement: étape 2, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement: étape 2, image 2 de 2
    • Lift the phone unit out of the back cover.

  3. Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the midframe screws: étape 3, image 1 de 1
    • Remove the nineteen 3.2 mm long T3 screws securing the plastic midframe.

  4. Motorola Moto E4 Plus LCD and Digitizer Replacement, Release the midframe clips: étape 4, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement, Release the midframe clips: étape 4, image 2 de 2
    • The plastic midframe is still held in place with clips.

    • Insert the flat end of a spudger into the midframe seam at the bottom left corner of the phone (near the microphone hole).

    • Twist the spudger to release the plastic clip.

    • Repeat the process for the clip near the top right corner of the phone.

  5. Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the midframe: étape 5, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the midframe: étape 5, image 2 de 2
    • Lift the bottom edge of the plastic midframe upwards until the clips along the top edge release.

    • Remove the plastic midframe.

    • To reattach the plastic midframe, line up the midframe to the phone and squeeze along the edges to engage the clips.

  6. Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the battery: étape 6, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the battery: étape 6, image 2 de 2
    • Use the point of a spudger to pry up and disconnect the battery connector from its motherboard socket.

  7. Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the display cable: étape 7, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the display cable: étape 7, image 2 de 2
    • Use the point of a spudger to pry up and disconnect the display cable from its motherboard socket, near the bottom left corner of the motherboard.

  8. Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the antenna cable: étape 8, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the antenna cable: étape 8, image 2 de 2
    • Use the point of a spudger to pry up and disconnect the antenna cable from its motherboard socket.

  9. Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the interconnect cable: étape 9, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the interconnect cable: étape 9, image 2 de 2
    • Use the point of a spudger to pry up and disconnect the interconnect cable from its motherboard socket.

  10. Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the motherboard screws: étape 10, image 1 de 1
    • Remove the two black 3.2 mm long T3 screws securing the motherboard.

  11. Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the motherboard: étape 11, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the motherboard: étape 11, image 2 de 2
    • Grasp the motherboard by the top corners and lift it out of the phone.

    • Remove the motherboard.

  12. Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the antenna: étape 12, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the antenna: étape 12, image 2 de 2
    • Use the point of a spudger to pry up and disconnect the antenna cable from its daughterboard socket.

  13. Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the daughterboard connectors: étape 13, image 1 de 3 Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the daughterboard connectors: étape 13, image 2 de 3 Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the daughterboard connectors: étape 13, image 3 de 3
    • Use the point of a spudger to pry up and disconnect the interconnect cable from its daughterboard socket.

    • Pry up and disconnect the fingerprint sensor cable next to it from the daughterboard.

  14. Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the daughterboard screws: étape 14, image 1 de 1
    • Remove the two 3.2 mm long T3 screws securing the daughterboard.

  15. Motorola Moto E4 Plus LCD and Digitizer Replacement, Loosen the daughterboard: étape 15, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement, Loosen the daughterboard: étape 15, image 2 de 2
    • Insert the point of a spudger under the bottom right corner of the daughterboard and pry up to loosen the daughterboard.

  16. Motorola Moto E4 Plus LCD and Digitizer Replacement, Loosen the vibration motor: étape 16, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement, Loosen the vibration motor: étape 16, image 2 de 2
    • Insert the point of a spudger underneath the vibration motor and pry upwards to loosen it.

  17. Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the daughterboard: étape 17, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the daughterboard: étape 17, image 2 de 2
    • Grasp the daughterboard by the edges and lift it out of its recess.

    • Remove the daughterboard. The vibration motor will be attached to it.

  18. Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the display ground: étape 18, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement, Disconnect the display ground: étape 18, image 2 de 2
    • Use the point of a spudger to pry up and disconnect the display grounding cable from the frame.

    • When you install the replacement cable, be sure that it is properly positioned with the gold side facing up.

  19. Motorola Moto E4 Plus LCD and Digitizer Replacement, Heat the display adhesive: étape 19, image 1 de 1
    • Prepare an iOpener and apply it to the display for at least two minutes to loosen the adhesive underneath.

  20. Motorola Moto E4 Plus LCD and Digitizer Replacement, Loosen the display: étape 20, image 1 de 3 Motorola Moto E4 Plus LCD and Digitizer Replacement, Loosen the display: étape 20, image 2 de 3 Motorola Moto E4 Plus LCD and Digitizer Replacement, Loosen the display: étape 20, image 3 de 3
    • Once the screen is warm to the touch, apply a suction cup near the top edge of the phone below the earpiece speaker.

    • If the phone's screen is cracked, the suction cup may not stick. Try lifting it with strong tape, or superglue the suction cup in place and allow it to cure so you can proceed.

    • Pull up the suction cup, and insert the tip of an opening pick under the display where the earpiece speaker is located.

    • Slide the opening pick to the top left corner of the phone to cut the adhesive.

  21. Motorola Moto E4 Plus LCD and Digitizer Replacement: étape 21, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement: étape 21, image 2 de 2
    • Insert a second opening pick and slide it to the top right corner of the phone.

  22. Motorola Moto E4 Plus LCD and Digitizer Replacement: étape 22, image 1 de 3 Motorola Moto E4 Plus LCD and Digitizer Replacement: étape 22, image 2 de 3 Motorola Moto E4 Plus LCD and Digitizer Replacement: étape 22, image 3 de 3
    • If cutting becomes too difficult, reheat and reapply the iOpener to the screen.

    • Slide the opening pick from the top right corner down the right edge of the phone and cut the adhesive with it.

    • While cutting, make sure the pick slides under the display panel and not just between the display and the front glass.

    • Continue sliding the opening pick around the bottom right corner of the phone.

  23. Motorola Moto E4 Plus LCD and Digitizer Replacement: étape 23, image 1 de 3 Motorola Moto E4 Plus LCD and Digitizer Replacement: étape 23, image 2 de 3 Motorola Moto E4 Plus LCD and Digitizer Replacement: étape 23, image 3 de 3
    • Slide the opening pick along the bottom edge of the phone and cut the adhesive.

    • Be careful around the home button, inserting only the tip of the opening pick to prevent damaging the button.

  24. Motorola Moto E4 Plus LCD and Digitizer Replacement: étape 24, image 1 de 2 Motorola Moto E4 Plus LCD and Digitizer Replacement: étape 24, image 2 de 2
    • Repeat the previous heating and cutting procedure on the left edge of the phone to cut the remaining adhesive.

    • Don't completely remove the display yet! The fingerprint and display flex cables are still threaded through the midframe.

  25. Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the LCD and digitizer: étape 25, image 1 de 3 Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the LCD and digitizer: étape 25, image 2 de 3 Motorola Moto E4 Plus LCD and Digitizer Replacement, Remove the LCD and digitizer: étape 25, image 3 de 3
    • Carefully thread the display cable at the top and the fingerprint sensor cable on the bottom through their gaps in the midframe.

    • Remove the LCD and digitizer.

    • Remove any remaining adhesive from the midframe, and clean the glued areas with isopropyl alcohol and a lint-free cloth.

    • In case your new LCD and digitizer doesn't include the fingerprint sensor, you will need to continue with the fingerprint sensor guide to transfer it to the new LCD and digitizer.

    • Carefully compare your replacement part with your screen. You may need to transfer minor parts such as earpiece bezel to the new part.

Conclusion

To reassemble your device, follow these instructions in reverse order.

If possible, turn on your phone and test your repair before installing new adhesive and resealing the phone.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Moto E4 Plus Answers community for help.

2 autres ont terminé cette réparation.

Arthur Shi

Membre depuis le 03/01/2018

212 118 Réputation

442 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

139 membres

15 781 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 9

30 derniers jours : 54

Total : 2,754