Réparez vos affaires Communauté Boutique

Nikon COOLPIX S610c Rear Casing Replacement

Introduction

If your rear casing needs to be replaced, if it's been cracked for example, follow this guide to remove the current rear case. In this guide ZxY denotes a screw with Z-length and Y-width.

Ce dont vous avez besoin

  1. Nikon COOLPIX S610c Rear Casing Replacement, Battery: étape 1, image 1 de 1

    • On the bottom right of the camera, locate the battery flap switch.

    Modifier

  2. Nikon COOLPIX S610c Rear Casing Replacement: étape 2, image 1 de 1

    • Move this switch to the right so the battery flap can flip open.

    Modifier

  3. Nikon COOLPIX S610c Rear Casing Replacement: étape 3, image 1 de 1

    • Slide the orange switch to the right as shown. Now the battery can be pulled out. Reverse these steps to re-install.

    Modifier

  4. Nikon COOLPIX S610c Rear Casing Replacement, Rear Casing: étape 4, image 1 de 1

    • Remove the three 3x3mm screws attached to the rear casing.

    Modifier

  6. Nikon COOLPIX S610c Rear Casing Replacement: étape 5, image 1 de 1

    • The panel can be identified by the wifi logo on its upper half on the camera's side.

    • Remove the 5x3mm screw holding down the panel on the side closest to the lens.

    Modifier

  7. Nikon COOLPIX S610c Rear Casing Replacement: étape 6, image 1 de 1

    • Pry the panel off from the bottom using your fingernail.

    Modifier

  8. Nikon COOLPIX S610c Rear Casing Replacement: étape 7, image 1 de 1

    • Remove the 3x2mm screw underneath the panel near the top of the camera.

    Modifier

  9. Nikon COOLPIX S610c Rear Casing Replacement: étape 8, image 1 de 2 Nikon COOLPIX S610c Rear Casing Replacement: étape 8, image 2 de 2

    • Remove the 4x3mm on the opposite side near the selector wheel.

    • Remove the 2x2mm and 3x2mm screws underneath the a/v flap.

    Modifier

  10. Nikon COOLPIX S610c Rear Casing Replacement: étape 9, image 1 de 2 Nikon COOLPIX S610c Rear Casing Replacement: étape 9, image 2 de 2

    • Pry the back panel away from the body of the camera, using the space you just opened up.

    • Be careful not to damage the ribbon cable on the opposite end of the camera.

    • A small piece of the frame of the camera may fall off, but it can be easily put back into place during reassembly.

    Modifier

  11. Nikon COOLPIX S610c Rear Casing Replacement: étape 10, image 1 de 2 Nikon COOLPIX S610c Rear Casing Replacement: étape 10, image 2 de 2

    • Pry up the plastic ribbon connectors on the body of the camera to release the ribbon cables.

    • The center connector is detached by flipping the black latch up and away from the center of the camera.

    • The smaller connector is detached by flipping the tan latch up and away from the edge of the camera.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 5 autres contributeurs

Kevin Backers

Membre depuis le 01/26/12

301 Réputation

4 tutoriels rédigés

Badges: 6

+ 3 badges supplémentaires

Équipe

Cal Poly, Team 9-5, Regan Winter 2012 Membre de l'équipe Cal Poly, Team 9-5, Regan Winter 2012

CPSU-REGAN-W12S9G5

5 membres

12 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 875