Réparez vos affaires

Droit à la réparation

Boutique

Nikon Coolpix P4 Flash Bulb Replacement

Rédigé par : Luke Baumann (et 5 autres contributeurs)
  • Commentaires : 1
  • Favoris : 3

Difficulté

Difficile

Étapes

30

Temps nécessaire

20 minutes

Sections

5

Drapeaux

2

Bullets!

Puces !

Une bonne utilisation des balises, de la couleur et/ou du format des puces donnera de la clarté à ce tutoriel !

Markup Mishap

Problème de balise

Ce tutoriel nécessite de meilleures balises. Améliorez-le en corrigeant ou rajoutant des balises.

Introduction

Refer to the lens replacement guide for direction on disassembly.

  1. 'Click' the battery door over to the side.

    • 'Click' the battery door over to the side.

    Modifier

  2. Open the battery door. Inside is the memory card and the battery.

    • Open the battery door. Inside is the memory card and the battery.

    • Click over the orange tab and take out the battery.

    • Close the battery lid by pushing it down and sliding it back.

    Modifier

  3. Remove the four screws located on bottom of camera. (.086in screws)

    • Remove the four screws located on bottom of camera. (.086in screws)

    Modifier

  4. Remove the two screws, then remove the panel. (.113in screws) Remove the two screws, then remove the panel. (.113in screws)

    • Remove the two screws, then remove the panel. (.113in screws)

    Modifier

  5. Remove panel on right side (front view) by removing these two screws. (.196in screws) Remove single screw set underneath panel. (0.083in screw) Remove single screw set underneath panel. (0.083in screw)

    • Remove panel on right side (front view) by removing these two screws. (.196in screws)

    • Remove single screw set underneath panel. (0.083in screw)

    Modifier

  6. Remove the two screws attaching the back panel to the body on the left side. (.188in screws)

    • Remove the two screws attaching the back panel to the body on the left side. (.188in screws)

    Modifier

  7. Gently pull off back cover

    • Gently pull off back cover

    Modifier

  8. Remove the two screws holding on the back panel. Then remove the three screws on the A/V Out tab (left side). (.188in screws) Remove tab.

    • Remove the two screws holding on the back panel. Then remove the three screws on the A/V Out tab (left side). (.188in screws)

    • Remove tab.

    Modifier

  9. Remove the two screws attaching the front panel to the body on the left side. (.18in screws)

    • Remove the two screws attaching the front panel to the body on the left side. (.18in screws)

    Modifier

  10. Flip up front panel.

    • Flip up front panel.

    • There should be wires still attaching the panel to body. DO NOT TRY TO PULL OFF COMPLETELY

    Modifier

  11. Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète

    Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète

  12. Remove three screws as shown. (Right screw:0.084in, Left screw:0.088in, Middle screw:0.114in)

    • Remove three screws as shown. (Right screw:0.084in, Left screw:0.088in, Middle screw:0.114in)

    Modifier

  13. Carefully pull orange LCD connector up and out of the port.

    • Carefully pull orange LCD connector up and out of the port.

    • Be careful to pull vertically while pushing the black tab upwards

    Modifier

  14. Remove the screw below the LCD (.124in)

    • Remove the screw below the LCD (.124in)

    Modifier

  15. Carefully pull out the plug connecting the LCD to the motherboard.

    • Carefully pull out the plug connecting the LCD to the motherboard.

    Modifier

  16. You can now remove the LCD from the camera body.

    • You can now remove the LCD from the camera body.

    • Insert new LCD and reassemble using the steps in reverse order.

    Modifier

  17. Remove the screw to the right of the flash.

    • Remove the screw to the right of the flash.

    • Remove the screw to the right of the microphone on the bottom. (0.124in)

    Modifier

  18. Remove the two screws on the right side of the camera. (0.115 in screws)

    • Remove the two screws on the right side of the camera. (0.115 in screws)

    Modifier

  19. Remove the four bottom screws. (0.116(fat head)-center screw, 0.112(skinny head)-other screws)

    • Remove the four bottom screws. (0.116(fat head)-center screw, 0.112(skinny head)-other screws)

    Modifier

  20. Remove the 7 screws from the back of the camera. (0.111 in screws)

    • Remove the 7 screws from the back of the camera. (0.111 in screws)

    Modifier

  21. Remove the plug that connects the lens to the left side of the motherboard by firmly grasping the base of the plug and pulling gently sideways away from the camera.

    • Remove the plug that connects the lens to the left side of the motherboard by firmly grasping the base of the plug and pulling gently sideways away from the camera.

    Modifier

  22. Remove the right panel.

    • Remove the right panel.

    Modifier

  23. Remove the screw from the top of the camera. (0.112 in screws)

    • Remove the screw from the top of the camera. (0.112 in screws)

    Modifier

  24. Remove the three screws from the motherboard. (0.112 in screws)

    • Remove the three screws from the motherboard. (0.112 in screws)

    • Detach the orange tab with the foam on top. It will click out of place.

    Modifier

  25. Remove the motherboard by pulling it up, out of the port.

    • Remove the motherboard by pulling it up, out of the port.

    Modifier

  26. Carefully remove the tab that connects the flash to the motherboard from the port by gently pulling connector to the right, out of its port.

    • Carefully remove the tab that connects the flash to the motherboard from the port by gently pulling connector to the right, out of its port.

    • Be careful when removing the connector.

    Modifier

  27. Remove the motherboard from camera body.

    • Remove the motherboard from camera body.

    • Replace with a new motherboard and follow the steps in reverse order to reassemble.

    Modifier

  28. Remove the orange plug by carefully pulling it out. It snaps in and out of place.

    • Remove the orange plug by carefully pulling it out. It snaps in and out of place.

    Modifier

  29. Remove flash unit from it's place in the camera.

    • Remove flash unit from it's place in the camera.

    • The flash unit is still attached to the camera.

    Modifier

  30. Remove the lens from the camera.

    • Remove the lens from the camera.

    Modifier

  31. Remove the tab connecting the flash to the motherboard by gently pulling the connector sideways out of its port, away from flash unit.

    • Remove the tab connecting the flash to the motherboard by gently pulling the connector sideways out of its port, away from flash unit.

    • Unsolder red and black wires.

    • Remove the flash unit.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 5 autres contributeurs

Luke Baumann

Membre depuis le 13/04/2011

128 Réputation

5 tutoriels rédigés

Badges: 10

+ 7 badges supplémentaires

Équipe

Cal Poly, Team 8-5, Regan Spring 2011 Membre de l'équipe Cal Poly, Team 8-5, Regan Spring 2011

CPSU-REGAN-S11S8G5

4 membres

10 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 2

Total : 3,435