Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Remplissez une casserole ou une poêle avec suffisamment d'eau pour immerger complètement un iOpener.
-
Faites chauffer l'eau jusqu'à ébullition. Puis éteignez le feu.
-
Placez un iOpener dans l'eau chaude pendant 2 à 3 minutes. Assurez-vous que l'iOpener est complètement immergé dans l'eau.
-
Utilisez des pinces pour extraire l'iOpener chauffé de l'eau chaude.
-
Séchez soigneusement l'iOpener avec une serviette.
-
Votre iOpener est prêt à être utilisé ! Si vous devez réchauffer l'iOpener, portez l'eau à ébullition, éteignez le feu et placez l'iOpener dans l'eau pendant 2 à 3 minutes.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lay a warm iOpener over the LCD glass to soften the adhesive holding it in place.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert a curved razor blade between the LCD glass cover and the body of D800.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Slide the curved razor blade along the front edge of the LCD.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Bring the blade around the corner of the LCD closest to the shutter button.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert the curved razor blade between the long edge of the LCD and the body of the D800.
-
Use the blade to pry the edge of the glass off the LCD.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Work your blade towards the corner nearest the lens.
-
Again, use the blade to separate the glass from the LCD panel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
While lifting up with the razor blade, insert a plastic opening pick underneath the LCD glass.
-
Remove the razor blade.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Slide the pick along the top edge of the glass, prying up on the glass against the plastic body as you go.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Leave the first opening pick underneath the front-right corner of the glass.
-
Insert a second opening pick underneath the panel from the back-left side of the display.
-
Slide the pick right, prying up the glass panel as you go.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Once the glass is mostly separated from the camera, peel the panel completely off the LCD screen.
-
At this point there may be some adhesive tape connecting the glass to the camera. If so, simply pull the glass up until it's free.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using rubbing alcohol and a q-tip, clean the old adhesive strips and any residue off the LCD screen.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Carefully align the new LCD protective glass over the display.
-
Lower the left edge of the glass onto the display and press it firmly against the edge of the LCD window.
-
Ease the right edge into place.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Press down on the edges of the display to ensure that the glass is strongly-adhered to the LCD.
-
Annulation : je n'ai pas terminé ce tutoriel.
9 autres ont terminé cette réparation.