Aller au contenu principal

Nintendo 3DS XL Left Bumper Replacement

Ce dont vous avez besoin

  1. Nintendo 3DS XL Left Bumper Replacement, Left Bumper: étape 1, image 1 de 1
    • Remove the SD card and the game cartridge from the device.

  2. Nintendo 3DS XL Left Bumper Replacement, Battery removal: étape 2, image 1 de 2 Nintendo 3DS XL Left Bumper Replacement, Battery removal: étape 2, image 2 de 2
    • Locate the battery cover panel on the back of the device.

    • Unscrew the two screws on the battery cover panel with a Phillips #00 screwdriver.

    • Remove the battery and battery cover panel.

  3. Nintendo 3DS XL Left Bumper Replacement: étape 3, image 1 de 1
    • Remove the four screws on the battery panel using the Phillips #00 screwdriver.

  4. Nintendo 3DS XL Left Bumper Replacement: étape 4, image 1 de 1
    • Locate the two screw covers on the bottom of the back panel, near the middle of the device.

    • These sticker-like covers are small, round, and made of rubber or plastic.

    • Insert the tip of a flathead screwdriver or spudger and gently pry the cover off by applying upward pressure.

    • You may need to wiggle the tool back and forth a bit to loosen the two covers.

    • Remove the two screws located behind the screw covers using a Phillips #00 screwdriver.

  5. Nintendo 3DS XL Left Bumper Replacement: étape 5, image 1 de 2 Nintendo 3DS XL Left Bumper Replacement: étape 5, image 2 de 2
    • Remove the screw near the game card compartment using a Phillips #00 screwdriver.

  6. Nintendo 3DS XL Left Bumper Replacement: étape 6, image 1 de 2 Nintendo 3DS XL Left Bumper Replacement: étape 6, image 2 de 2
    • Lift the back panel off of the device.

    • Be cautious not to pull any ribbons or cables from the motherboard as you remove the back panel.

    • Locate and disconnect the ribbon cables from the motherboard by gently pulling on the tabs that hold them in place.

  7. Nintendo 3DS XL Left Bumper Replacement: étape 7, image 1 de 2 Nintendo 3DS XL Left Bumper Replacement: étape 7, image 2 de 2
    • Remove the three left bumper assembly screws using Phillips #00 screwdriver.

    • Once the three screws are removed, gently remove the left bumper assembly from the device.

    • The spring may eject from the assembly as you remove it.

    • Remove the hinge pin from the bumper assembly.

  8. Nintendo 3DS XL Left Bumper Replacement: étape 8, image 1 de 1
    • Separate the bumper from the bumper assembly

  9. Nintendo 3DS XL Left Bumper Replacement: étape 9, image 1 de 2 Nintendo 3DS XL Left Bumper Replacement: étape 9, image 2 de 2
    Outil utilisé dans cette étape :
    Microfiber Cleaning Cloths
    $3.99
    J'achète
    • Using a spudger or a flathead screwdriver, gently pull the ribbon cable straight out of the connector in order to remove it.

    • The ribbon cable can be removed by other means such as using gloves or a microfiber cloth if preferred.

    • Replace the left bumper ribbon cable.

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autres ont terminé cette réparation.

Jack Belcher

Membre depuis le 10/26/21

187 Réputation

1 tutoriel rédigé

Équipe

3 commentaires

No steps on how to install the new bumper?

Alex Tomalty - Réponse

good but i wish there were reinstall instructions

Rowan Webb - Réponse

I think that it's just basically do the steps backwards then you have it fixed.

Ender - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 6

7 derniers jours : 36

30 derniers jours : 191

Total : 4,687