Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Boutique

Introduction

Replace the power switch on the Nintendo DS Lite.

  1. Unscrew the Phillips screw securing the battery cover to the lower case. The screw remains captive to the battery cover.
    • Unscrew the Phillips screw securing the battery cover to the lower case.

    • The screw remains captive to the battery cover.

    • Pry the battery cover upward with a spudger or fingernail, and lift out of the lower case.

    A Phillips #000 (PH000) seems to give a more secure fit (no slipping) than the stated Phillips #00.

    Ritchie - Réponse

    This will be good for mods

    Matthew Bevins - Réponse

    I'm having a problem getting the screw to unscrew. I have the right Phillips ( it was included with all the stuff I got this) Any tips. it doesn't look like the screw is spinning but i haven't played my Nintendo DS Lite for 3 years.

    whittlegirls - Réponse

    bonjour j’ai une petite question pour vous fais trés longtemps que j’ai pas utiliser mon nintendo ds lite et quand je le branche il allume 1 fois orange après il s’enteint même s’il est brancher ça veux tu dire qu’il faut que je change de batterie ? Merci

    Marie-Julie Richer - Réponse

  2. Wedge the edge of a spudger in between the side of the battery and the lower case housing and pry upward to dislodge the battery.
    • Wedge the edge of a spudger in between the side of the battery and the lower case housing and pry upward to dislodge the battery.

    • Remove the battery from the DS Lite.

  3. Use the tip of a spudger to pry both rubber feet off the DS Lite. Use the tip of a spudger to pry both rubber feet off the DS Lite.
    • Use the tip of a spudger to pry both rubber feet off the DS Lite.

  4. Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète

    Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète
  5. Remove the following screws securing the lower case to the body of the DS Lite:
    • Remove the following screws securing the lower case to the body of the DS Lite:

    • Two 4.3 mm gold Phillips screws

    • One 3.9 mm black Tri-Wing screw

    • One 3.3 mm silver Phillips screw

    • Three 5.5 mm silver Tri-Wing screws

    Not mentioned is to remove the jumper/connector below the word "SLOT-2". Case WILL NOT separate otherwise.

    Kayla - Réponse

    In the separation step below, the third picture show the case with the jumper/connector removed.

    Kayla - Réponse

    I cannot remove the tri-wing screws.

    Zach Smith - Réponse

  6. Insert the edge of a spudger in between the lower and upper case near the top right corner of the DS Lite. Carefully run the spudger along the right edge of the DS Lite, creating an opening in the process. Continue running the spudger along the backside of the DS Lite until the majority of the lower case has been separated from the upper case.
    • Insert the edge of a spudger in between the lower and upper case near the top right corner of the DS Lite.

    • Carefully run the spudger along the right edge of the DS Lite, creating an opening in the process.

    • Continue running the spudger along the backside of the DS Lite until the majority of the lower case has been separated from the upper case.

    Don’t forget to remove the GBA cartridge placeholder before removing the backside

    Cees Jan de Boer - Réponse

  7. Lift the lower case away from the rest of the DS Lite.
    • Lift the lower case away from the rest of the DS Lite.

    • Pull carefully. Some units are sealed with adhesive, and pulling too hard can damage the power switch.

    When you reassemble, make sure that you have the volume and power buttons in place, and make sure they are in the right position to line up with the switches on the motherboard. If they are not aligned, you risk snapping off the tiny switches on the motherboard (in which case, you are in for some soldering work).

    Eric - Réponse

    I should have read the comments first - broke off the power switch because I didn't know about aligning it. No way I can do soldering, guess it's for the dustbin :-(

    Emma -

    Whoops, remembered the power button but forgot the volume slider.

    I'll do it later.

    analbonghits -

    There is no way that the fact you have to line up the volume and power switch toggles upon reassembly is not in this guide. I just carefully followed this guide to replace the shoulder buttons but ruined my DS lite because I didn’t read these (practically hidden comments due to the design of the website) comments and broke the power switch. Thankfully there are 150 million DS I can buy second hand but “repeat the steps backwards” wasn’t sufficient in this repair. And that’s what this website is for.

    Ryan -

  8. Use a pair of tweezers to carefully remove the power switch.
    • Use a pair of tweezers to carefully remove the power switch.

    Ummmm. My switch won’t go back in.

    Tak Toyota - Réponse

Conclusion

To reassemble your device, follow these instructions in reverse order.

16 autre(s) ont terminé cette réparation.

Philip

Membre depuis le 20/01/2010

500 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 16-30, Maness Winter 2010 Membre de l'équipe Cal Poly, Team 16-30, Maness Winter 2010

CPSU-MANESS-W10S16G30

4 membres

13 tutoriels rédigés

What about replacing the soldered portion of the switch? The tip that moves with the plastic to turn the handheld on/off has broken off of mine

Wicked Gamer - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 6

7 derniers jours : 75

30 derniers jours : 317

Total : 43,955