Aller au contenu principal

Nintendo DS Main Circuit Board Replacement

Ce dont vous avez besoin

  1. Nintendo DS Main Circuit Board Replacement, Battery: étape 1, image 1 de 3 Nintendo DS Main Circuit Board Replacement, Battery: étape 1, image 2 de 3 Nintendo DS Main Circuit Board Replacement, Battery: étape 1, image 3 de 3
    • Remove the cartridge from the console.

    • Use a Phillips #00 Screwdriver to remove the screw securing the battery door to the rear case.

    • Remove the battery door.

    • In the images, it shows that the fixer is using a flathead screwdriver. This flathead screwdriver will work just like the Phillips #00 Screwdriver.

  2. Nintendo DS Main Circuit Board Replacement: étape 2, image 1 de 1
    • Use a plastic opening tool or spudger to pry out the battery from the bottom. If a plastic opening tool or spudger isn't available, your fingernails may work.

  3. Nintendo DS Main Circuit Board Replacement: étape 3, image 1 de 1
    • Remove the battery from the Nintendo DS.

  4. Nintendo DS Main Circuit Board Replacement, Back Panel: étape 4, image 1 de 1
    • Remove the seven 6.4mm Y00 screws located on the back.

    • If your DS has a lanyard attached to it, you can remove it to make the process of opening the top-left screw easier.

  5. Nintendo DS Main Circuit Board Replacement: étape 5, image 1 de 3 Nintendo DS Main Circuit Board Replacement: étape 5, image 2 de 3 Nintendo DS Main Circuit Board Replacement: étape 5, image 3 de 3
    • With your hands, pry the back panel off the main case.

    • Separate the back from the front, and set it aside.

  6. Nintendo DS Main Circuit Board Replacement, Main Circuit Board: étape 6, image 1 de 1
    • Using a Phillips #00 screwdriver, remove the four screws on the circuit board.

    • Be careful NOT to slip with the screwdriver, you can damage the circuit board!

  7. Nintendo DS Main Circuit Board Replacement: étape 7, image 1 de 3 Nintendo DS Main Circuit Board Replacement: étape 7, image 2 de 3 Nintendo DS Main Circuit Board Replacement: étape 7, image 3 de 3
    • Unlock the two large ribbon cables by moving the black clip up.

    • Carefully pull the ribbon cables down and out with your fingers.

    • Do not use pliers to pull the cables, as they can be damaged easily.

  8. Nintendo DS Main Circuit Board Replacement: étape 8, image 1 de 2 Nintendo DS Main Circuit Board Replacement: étape 8, image 2 de 2
    • Locate the two small ribbon cables, beneath the rightmost large ribbon cable.

    • Slide the locks for the small ribbon cables down to the side, and remove the cables.

    • It may be useful to use tweezers to remove the small ribbon cables.

    • Be careful not to damage the delicate ribbon cables.

  9. Nintendo DS Main Circuit Board Replacement: étape 9, image 1 de 2 Nintendo DS Main Circuit Board Replacement: étape 9, image 2 de 2
    • Locate the Wifi antenna pigtail connector.

    • Remove the antenna by grasping it at the head with tweezers. Using a slight rocking motion, pull up to dislodge the connector.

  10. Nintendo DS Main Circuit Board Replacement: étape 10, image 1 de 1
    • Feed the ribbon cables through the opening on the board.

    • Pull up and remove the circuit board, and set it aside.

Conclusion

To reassemble your device, follow these instructions in reverse order.

20 autres ont terminé cette réparation.

kingdesmond

Membre depuis le 10/27/09

2 050 Réputation

1 tutoriel rédigé

Équipe

Cal Poly, Team 18-3, Maness Fall 2009 Membre de l'équipe Cal Poly, Team 18-3, Maness Fall 2009

CPSU-MANESS-F09S18G3

4 membres

28 tutoriels rédigés

Un commentaire

This was really helpful. Thank you!

Jess Anderson - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 4

7 derniers jours : 39

30 derniers jours : 241

Total : 27,767