Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Retirez les deux vis cruciformes Phillips fixant le cache de la batterie à la console portable.
-
Retirez le cache de la batterie de l'arrière de la DSi XL.
-
-
-
Retirez les quatre cache-vis en caoutchouc du boîtier inférieur en les soulevant à l'aide d'une punaise.
-
-
-
Avec une spatule (spudger), faites levier pour enlever la nappe du microphone de la carte mère.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
With the console still upside-down, open the DSi XL slightly.
-
Push the lower display away from the upper case.
-
Remove the lower display from the DSi XL.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the DSi XL over and open the display.
-
Use a pushpin to remove the four plastic screw covers on the front bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four 3.5 mm silver Phillips screws securing the rear bezel to the front bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using two hands, gently slide the rear bezel upwards.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert a spudger into the gap between the front and rear bezel.
-
Rotate the spudger away from the DSi XL, prying the two bezels apart.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
In the same manner as described above, continue prying along the top edge of the front and rear bezels.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using the flat end of a spudger, pry the rear camera off the rear bezel.
-
Remove the rear bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the Phillips screw holding the metal securing bracket in place.
-
Lift the metal bracket off the camera.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the Wi-Fi antenna off the front display bezel.
-
De-route the Wi-Fi antenna cable from its grooves at the bottom of the front display bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the Wi-Fi antenna cable through the right hinge connecting the front bezel and upper case.
-
Use the pointed end of a spudger to guide the connector at the end of the Wi-Fi antenna cable through the hinge.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using a pair of tweezers, pull the microphone out of its housing in the front bezel.
-
De-route the microphone cable, and pull it through the right hinge.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using the flat end of a spudger, pry the left speaker out of its socket on the front bezel.
-
De-route the speaker cable along the top edge of the screen.
-
In the same manner described above, remove the right speaker from its socket on the front bezel.
-
Place both speakers on the back of the upper LCD.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the seven 2.5 mm silver screws securing the power board to the upper case.
-
Lift the power board up off the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel the rubber button pads off the backside of the D-pad and power button.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Push the D-pad up through its housing in the upper case. Remove the D-pad.
-
In the same way, remove the power button from the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using a pair of tweezers, remove the LED diffuser bracket and the LED diffuser from the upper case of the DSi XL.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Place the tip of a spudger in the LED diffuser compartment, on the face of the clutch hinge.
-
Push the clutch hinge to the left.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the left side of the front bezel away from the upper case.
-
Pull the front bezel to the left, separating the front bezel from the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the camera and upper LCD ribbon cables between your thumb and forefinger, pulling them out of the upper case slightly, slide them down through the slit in the upper case.
-
Rotate the front bezel assembly clockwise so that the ends of the camera and LCD cables slide sideways through the slit in the front bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Carefully coil the two ribbon cables together, so that the connectors are on the inside of the spool.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Holding the upper LCD and the cameras together, pull the cables through the hinge in the front bezel.
-
Uncoil the ribbon cables.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the hollow hinge pin out of the right side of the front bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Push the clutch hinge on the left side of the front bezel through its mount bracket.
-
Remove the clutch hinge.
-
Annulation : je n'ai pas terminé ce tutoriel.
Une autre personne a terminé cette réparation.