Aller au contenu principal

Nintendo Switch Micro SD Card Reader Replacement

Ce dont vous avez besoin

  1. Nintendo Switch Micro SD Card Reader Replacement, Release the Joy Con controller locking tabs: étape 1, image 1 de 3 Nintendo Switch Micro SD Card Reader Replacement, Release the Joy Con controller locking tabs: étape 1, image 2 de 3 Nintendo Switch Micro SD Card Reader Replacement, Release the Joy Con controller locking tabs: étape 1, image 3 de 3
    • Before you begin this repair, make sure the device is completely powered off.

    • Press and hold down the small round button on the back of the Joy Con controller.

    • While you hold down the button, slide the controller upward.

  2. Nintendo Switch Micro SD Card Reader Replacement, Remove the Joy Con controllers: étape 2, image 1 de 3 Nintendo Switch Micro SD Card Reader Replacement, Remove the Joy Con controllers: étape 2, image 2 de 3 Nintendo Switch Micro SD Card Reader Replacement, Remove the Joy Con controllers: étape 2, image 3 de 3
    • Continue sliding the Joy Con upward until it's completely removed from the console.

    • Repeat this same process for the other Joy Con.

  3. Nintendo Switch Micro SD Card Reader Replacement, Remove the back-side screws: étape 3, image 1 de 1
    Outil utilisé dans cette étape :
    Magnetic Project Mat
    $19.95
    J'achète
    • Use a Y00 screwdriver to remove the four 6.3 mm-long screws securing the rear panel.

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

  4. Nintendo Switch Micro SD Card Reader Replacement, Remove the top and bottom screws: étape 4, image 1 de 2 Nintendo Switch Micro SD Card Reader Replacement, Remove the top and bottom screws: étape 4, image 2 de 2
    • Use a JIS 000 driver or an official iFixit PH 000 driver to remove the following screws securing the rear panel:

    • One 2.5 mm-long screw on the top edge of the device

    • Two 2.5 mm-long screws on the bottom edge of the device

    • To prevent these tight screws from stripping, apply firm downward force, work slowly and try another JIS 000 or PH 000 driver if the screws won't come out.

  5. Nintendo Switch Micro SD Card Reader Replacement: étape 5, image 1 de 2 Nintendo Switch Micro SD Card Reader Replacement: étape 5, image 2 de 2
    • Use a JIS 000 screwdriver or an official iFixit PH 000 driver to remove the two 3.8 mm center screws on the sides of the device (one on each side).

  6. Nintendo Switch Micro SD Card Reader Replacement: étape 6, image 1 de 2 Nintendo Switch Micro SD Card Reader Replacement: étape 6, image 2 de 2
    • Use your finger to flip up the kickstand on the back of the device.

    • If there's a microSD card in the microSD card slot, remove it now before you continue to the next step.

  7. Nintendo Switch Micro SD Card Reader Replacement: étape 7, image 1 de 1
    • Use a JIS 000 screwdriver or an official iFixit PH 000 driver to remove the 1.6 mm screw in the kickstand well.

    • Close the kickstand.

  8. Nintendo Switch Micro SD Card Reader Replacement: étape 8, image 1 de 3 Nintendo Switch Micro SD Card Reader Replacement: étape 8, image 2 de 3 Nintendo Switch Micro SD Card Reader Replacement: étape 8, image 3 de 3
    • Open the game card cartridge flap.

    • The game card cartridge flap attaches to the other half of the plastic shell, preventing you from completely lifting up the rear panel if it's closed.

    • Lift the rear panel up from the bottom of the device and remove it.

  9. Nintendo Switch Micro SD Card Reader Replacement, Remove the microSD card reader: étape 9, image 1 de 1
    • Use a JIS 000 screwdriver to remove the 3.1 mm screw securing the microSD card reader to the device.

  10. Nintendo Switch Micro SD Card Reader Replacement: étape 10, image 1 de 2 Nintendo Switch Micro SD Card Reader Replacement: étape 10, image 2 de 2
    • Use your fingers or a pair of tweezers to lift the microSD card reader straight up from the device to disconnect and remove it.

    • During reassembly, make sure the press connector underneath the foam pad is firmly connected to the motherboard

Conclusion

Compare your new replacement part to the original part. You may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Nintendo Switch Answers community for help.

142 autres ont terminé cette réparation.

Craig Lloyd

Membre depuis le 02/10/16

35 418 Réputation

82 tutoriels rédigés

50 commentaires

My SD reader never worked.

Used this guide to find that it was never seated correctly. Reseated and now works perfectly. THANK YOU!

Finx O'Mally - Réponse

My console won’t boot if I have an SD card inserted after reseating it. What should I do?

Ewan MacInnis - Réponse

Easy guide, fixed my problem. Changed the SD card reader cause I was abusing of it by putting SD in and out constantly.

Nicola Bonardi - Réponse

Great guide! My 11-year-old son was able to fix his Switch himself with no difficulty.

Matt - Réponse

Some one can help me, when I tried to put the connector again I damage the fpc connector of the motherboard so I try to find out again can any one know the kind of model of this connector I really appreciate the help

Best regards

Philip Milian - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 91

7 derniers jours : 726

30 derniers jours : 3,503

Total : 191,314