Réparez vos affaires Communauté Boutique

Nintendo Wii Motherboard Cover Replacement

Conditions préalables uniquement
Ce tutoriel est uniquement destiné à être utilisé comme prérequis d'autres tutoriels. Il ne se suffit pas à lui-même.

Ce dont vous avez besoin

  1. Nintendo Wii Motherboard Cover Replacement, Motherboard Cover: étape 1, image 1 de 1

    • Use a pair of tweezers to lift the fan connector up and out of its socket on the logic board.

    • Be sure your tweezers are clamped down on the fan connector, not the socket on the motherboard.

    Traduire

  2. Nintendo Wii Motherboard Cover Replacement: étape 2, image 1 de 2 Nintendo Wii Motherboard Cover Replacement: étape 2, image 2 de 2

    • Remove the two 10 mm Phillips screws securing the fan to the fan shroud.

    • Remove the fan from the Wii.

    Traduire

  3. Nintendo Wii Motherboard Cover Replacement: étape 3, image 1 de 2 Nintendo Wii Motherboard Cover Replacement: étape 3, image 2 de 2

    • Use the tip of a spudger or another fine-pointed tool to carefully pry one of the black plastic retaining fingers attached to the fan shroud away from the Wi-Fi antenna board.

    • Lift the Wi-Fi antenna out of the fan shroud.

    Traduire

  4. Nintendo Wii Motherboard Cover Replacement: étape 4, image 1 de 1

    • Remove the single 10 mm Phillips screw securing the second Wi-Fi antenna to the top of the fan shroud.

    Traduire

  6. Nintendo Wii Motherboard Cover Replacement: étape 5, image 1 de 1

    • Remove the two pieces of tape securing the second Wi-Fi antenna cable to the plastic bracket near the heat sink.

    Traduire

  7. Nintendo Wii Motherboard Cover Replacement: étape 6, image 1 de 1

    • Carefully de-route both antennas from the frame of the Wii and lay them aside.

    Traduire

  8. Nintendo Wii Motherboard Cover Replacement: étape 7, image 1 de 2 Nintendo Wii Motherboard Cover Replacement: étape 7, image 2 de 2

    • Remove the three 10 mm Phillips screws securing the fan shroud to the Wii.

    • Lift the fan shroud off the heat sink and remove it from the Wii.

    Traduire

  9. Nintendo Wii Motherboard Cover Replacement: étape 8, image 1 de 3 Nintendo Wii Motherboard Cover Replacement: étape 8, image 2 de 3 Nintendo Wii Motherboard Cover Replacement: étape 8, image 3 de 3

    • Remove the following six screws securing the EMI fingers to the bottom panel:

    • Four 7 mm Phillips screws

    • Two 11.3 mm Phillips screws

    • Remove both sets of EMI fingers from the Wii.

    Traduire

  10. Nintendo Wii Motherboard Cover Replacement: étape 9, image 1 de 2 Nintendo Wii Motherboard Cover Replacement: étape 9, image 2 de 2

    • Remove the following three screws:

    • One 7 mm Phillips screw

    • Two 10 mm Phillips screws

    • Lift the bracket out of the Wii.

    Traduire

  11. Nintendo Wii Motherboard Cover Replacement: étape 10, image 1 de 3 Nintendo Wii Motherboard Cover Replacement: étape 10, image 2 de 3 Nintendo Wii Motherboard Cover Replacement: étape 10, image 3 de 3

    • Remove the three 10 mm Phillips screws securing the black bracket to the bottom panel near the front of the Wii.

    • Slightly lift the bracket and use your other hand to pull the retaining clip away from where the Wi-Fi antennas enter the motherboard sheild.

    • Remove the bracket from the Wii.

    • Be sure not to lose the small square nut loosely held by the black plastic bracket.

    Traduire

  12. Nintendo Wii Motherboard Cover Replacement: étape 11, image 1 de 1

    • Remove the nine remaining 7 mm Phillips screws securing the motherboard cover to the bottom panel.

    Traduire

  13. Nintendo Wii Motherboard Cover Replacement: étape 12, image 1 de 1

    • Carefully lift the motherboard cover off the motherboard, minding any cables that may get caught.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 974